[DESIGN PRECAUTIONS]DANGERIncorrect operation of the touch switch(s)may lead to a serious accident if the GOT backlight is goneout.When the GOT backlight goes out,the POWER LED flickers(green/orange)and the display sectiontums black and causes the monitor screen to appear blank,while the input of the touch switch(s)remains active.This may confuse an operator in thinking that the GOT is in "screensaver"mode,who then tries torelease the GOT from this mode by touching the display section,which may cause a touch switch tooperate.Note that the following occurs on the GOT when the backlight goes out..The POWER LED flickers (green/orange)and the monitor screen appears blankCAUTIONDo not bundle the control and munication cables with main-circuit,power or other wiring.Run the above cables separately from such wiring and keep them a minimum of 100mm(3.94in.)apart.Not doing so noise can cause a malfunction.[MOUNTING PRECAUTIONS]DANGERBe sure to shut off all phases of the external power supply used by the system before mounting orremoving the GOT main unit to/from the panel.Not doing so can cause the unit to fail or malfunction.Be sure to shut off all phases of the external power supply used by the system before mounting orremoving the munication unit,option function board or multi-color display board onto/from theGOT.Not doing so can cause the unit to fail or malfunction.When installing the multi-color display board,wear an earth band etc.to avoid the staticelectricity.Not doing so can cause a unit corruption.CAUTION●Use the GOT in the environment that satisfies the general specifications described in this manual.Not doing so can cause an electric shock,fire,malfunction or product damage or deterioration.When mounting the GOT to the control panel,tighten the mounting screws in the specified torquerange.Undertightening can cause the GOT to drop,short circuit or malfunction.Overtightening can cause a drop,short circuit or malfunction due to the damage of the screws or theGOT.A-2[MOUNTING PRECAUTIONS]CAUTIONWhen loading the munication unit to the GOT,fit it to the connection interface of the GOT andtighten the mounting screws in the specified torque range.Undertightening can cause the GOT to drop,short circuit or malfunction.Overtightening can cause a drop,failure or malfunction due to the damage of the screws or unit.When mounting the multi-color display board onto the GOT,tighten the mounting screws within thespecified torque range.Loose tightening may cause the unit and/or GOT to malfunction due to poor contact.Overtightening may damage the screws,unit and/or GOT;they might malfunction.Push the option function board onto the corresponding connector until it clicks,so that it will besecured fimmly.Push the multi-color display board onto the corresponding connector so that it will be secured firmly.When inserting a CF card into the GOT,push it into the insertion slot until the CF card eject buttonwill pop out.Failure to do so may cause a malfunction due to poor contact.When inserting/removing a CF card into/from the GOT,turn the CF card access switch off inadvance.Failure to do so may corrupt data within the CF card.When removing a CF card from the GOT,make sure to support the CF card by hand,as it may popout.Failure to do so may cause the CF card to drop from the GOT and break.[WIRING PRECAUTIONS]DANGERBe sure to shut off all phases of the external power supply used by the system before wiring.Failure to do so may result in an electric shock,product damage or malfunctions.A-3[WIRING PRECAUTIONS]CAUTIONAlways ground the FG terminal,LG terminal,and protective ground terminal of the GOT power to theprotective ground conductors dedicated to the GOT.Not doing so may cause an electric shock or malfunction.Terminal screws which are not to be used must be tightened always at torque 0.5 to 0.8 N-m.Otherwise there will be a danger of short circuit against the solderless temminals.Use applicable solderless terminals and tighten them with the specified torque.If any solderless spade terminal is used,it may be disconnected when the temminal screw esloose,resulting in failure.Correctly wire the GOT power supply section after confimming the rated voltage and terminalarrangement of the product.Not doing so can cause a fire or failure.Tighten the terminal screws of the GOT power supply section in the specified torque range.Undertightening can cause a short circuit or malfunction.Overtightening can cause a short circuit or malfunction due to the damage of the screws or the GOT.Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT.Not doing socan cause a fire,failure or malfunction.Plug the bus connection cable by inserting it into the connector of the connected unit until it"clicks".After plugging,check that it has been inserted snugly.Not doing so can cause a malfunction due to a contact fault.Plug the munication cable into the connector of the connected unit and tighten the mounting andterminal screws in the specified torque range.Undertightening can cause a short circuit or malfunction.Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.[TEST OPERATION PRECAUTIONS]DANGERWhen testing the operation (e.g.tuming bit devices ON/OFF or changing a current word devicevalue,a current or set timer/counter value,or a current buffer memory value),thoroughly read therelevant manual to fully understand the operating procedures.When testing,never change the dataof the devices that control the operation essential for the system.False output or malfunction can cause an accident.A-4[STARTUP/MAINTENANCE PRECAUTIONS]DANGERWhen power is on,do not touch the terminals.Doing so can cause an electric shock or malfunction.Connect the battery correctly.Do not discharge,disassemble,heat,short,solder or throw the battery into the fire.Incorrect handling may cause the battery to generate heat,burst or take fire,resulting in injuries orfiresBefore starting cleaning or terminal screw retightening,always switch off the power externally in allphases.Not switching the power off in all phases can cause a unit failure or malfunction.Undertightening can cause a short circuit or malfunction.Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.CAUTIONDo not disassemble or modify the unit.Doing so can cause a failure,malfunction,injury or fire.Do not touch the conductive and electronic parts of the unit directly.Doing so can cause a unit malfunction or failure.The cables connected to the unit must be run in ducts or clamped.Not doing so can cause the unit or cable to be damaged due to the dangling,motion or accidentalpulling of the cables or can cause a malfunction due to a cable connection fault.When unplugging the cable connected to the unit,do not hold and pull the cable portion.Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cableconnection fault.Do not drop the module or subject it to strong shock.A module damage may result.Do not drop or give an impact to the battery mounted to the unit.Doing so may damage the battery,causing the battery fluid to leak inside the battery.If the battery is dropped or given an impact,dispose of it without using.Before touching the unit,always touch grounded metal,etc.to discharge static electricity fromhuman body,etc.Not doing so can cause the unit to fail or malfunction.[BACKLIGHT REPLACEMENT PRECAUTIONS]!DANGERBe sure to shut off all phases of the external power supply of the GOT(and the controller in the caseof a bus topology)and remove the GOT from the control panel before replacing the backlight (whenusing the GOT with the backlight replaceable by the user).Not doing so can cause an electric shock.Replacing a backlight without removing the GOT from the control panel can cause the backlight orcontrol panel to drop,resulting in an injury.A-5[BACKLIGHT REPLACEMENT PRECAUTIONS]CAUTIONWear gloves for the backlight replacement when using the GOT with the backlight replaceable by theuser.Not doing so can cause an injury.Before replacing a backlight,allow 5 minutes or more after turning off the GOT when using the GOTwith the backlight replaceable by the user.Not doing so can cause a bum from heat of the backlight.[DISPOSAL PRECAUTIONS]CAUTIONWhen disposing of the product,handle it as industrial waste.[TRANSPORTATION PRECAUTIONS]CAUTIONWhen transporting lithium batteries,make sure to treat them based on the transport regulations.(Refer to Appendix 3 for details of the regurated units.)Make sure to transport the GOT main unit and/or relevant unit(s)in the manner they will not beexposed to the impact exceeding the impact resistance described in the general specifications of thismanual,as they are precision devices.Failure to do so may cause the unit to fail.Check if the unit operates correctly after transportation.A-6REVISIONSThe manual number is given on the bottom left of the back cover.Print DateManual NumberRevisionMar,2005SH(NA)-080544ENG-AFirst editionSH(NA)-080544ENG-BCompatible with GT Designer2 Version2.18U.Partial correctionsAbbreviations and generic terms in this manual,Chapter1,Section 1.1.1,1.1.2.1.1.3.2.1.2.2.1.2.2.2.2.3.1.24.2.2.4.3.24.4.2.4.5.2.5.2.5.1.2.5.3.2.6.1.2.7.1,2.8.1,2.92,2.9.3,2.9.4,2.9.5,3.1,3.2.1,3.2.2,3.3,3.3.1,3.32,3.3.3,3.4.1,3.8,4.1,4.2.1,4.3,4.3.1,4.3.2,4.4.1,4.42,4.4.7,4.7.3,App.1,INDEXPartial additionsSection2.6.2.7.2.8.3.4.3.5.4AdditionsSection2.2.3,3.2.3,3.2.4,4.2.2,4.4.6,Chapter5.6,7,89,10Section2.2.3→2.2.4，Section5.1→2.10，Section3.3.4→3.3.3，Section3.4.3→3.4.2，Section4.2.2→4.2.3，Section4.4.6→4.4.7，Section4.4.7→4.4.8,Section5.2→3.8，Section5.3+4.7Jan,2006SH(NA)-080544ENG-CCompatible with GT Designer2 Version2.27D.Partial correctionsAbout Manuals,Abbreviations and generic terms in this manual,Howto read thismanual,.Section3.1,3.4.2,4.4.6,5.4.12,7.4.1,8.4.11,9.2.1,9.4.8,10.2.1,App1AdditionsSection1.1.4,3.5.7Jun,2006SH(NA)-080544ENG-DCompatible with GT Designer2 Version2.32J.Partial correctionsAbout Manuals,Abbreviations and generic terms in this manual,Howto read thismanual,,Section1.1.1,1.12,2.3.1,3.2.1,3.3.2,4.1,5.1,5.3,6.1,6.2.2,6.4.1,6.42,7.1,72.1,72.4,8.2.1,8.4.2,8.4.11,10.2.1,10.2.3,App1AdditionsChapter1,Section2.1,3.2.4,8.2.3,9.2.1SH(NA)-080544ENG-ECompatible with GT Designer2 Version2.43V.Partial correctionsPartial additionsSection3.3.1,3.3.3,3.4.1(Continued to next page)A-7Print DateManual NumberRevisionMay,2007SH(NA)-080544ENG-FCompatible with GT Designer2 Version 2.58LPartial correctionsSection1.1.1,1.12,2.1,22.1,2.5.1,2.6.1,2.7.1,2.8.1,2.9.3,3.1,3.2.1,32.43.3.1,3.3.3,3.3.4,3.4.1,3.4.2,3.5.1to3.5.7,3.6.1to3.6.7,3.7.1,42.1,52.1,5.3.5.4.9t05.4.11.7.1,8.2.1.8.4.11.9.2.1.9.4.8Partial additionsSection5.2.3,5.4.1AdditionsSection3.3.5,3.8.5.4.12,14.10,Chapter11Section3.8→3.9，Section5.4.12→5.4.13，Section5.4.13→5.4.14Aug,2007SH(NA)-080544ENG-GCompatible with GT Designer2 Version 2.63RPartial correctionsSection3.2.1,8.2.3,8.3,8.4.1,8.4.6Partial additionsChapter1,Section1.1.1,1.1.2,1.14,22.3,3.2.2,3.2.3,32.4,6.2.2,62.3,8.2.1,8.4.4,10.2.1,10.2.2,10.2.3,10.4,10.5,11.2.1,App1AdditionsSection 11.5,Chapter 12Section11.5→11.6Dec.,2007SH(NA)-080544ENG-HCompatible with GT Designer2 Version 2.72APartial correctionsSection1.1.3.1.1.4.3.2.1,3.3.3.10.2.10.2.1,11.3.1,11.32.11.4.1,11.52.11.5.3.12.4Partial additionsSection1.1.1,1.1.2,2.1,2.3.1,3.2.4,3.4.1,11.1,112.1,112.3,113.3AdditionsSection 11.3.4Feb.,2008SH(NA)-080544ENG-ICompatible with GT Designer2 Version 2.77FPartial correctionsSection1.1.3,2.2.3.3.2.3,72.3Partial additionsChapter1,Section1.1.1,1.1.2,1.1.4,2.2.1,3.1,3.2.1,6.2.1,6.2.2,7.1,7.2.1,722,7.2.4,7.4.1to7.4.9,82,App1AdditionsChapter 13(Continued to next page)A-8Print DateManual NumberRevisionJun,2008SH(NA)-080544ENG-JCompatible with GT Designer2 Version 2.82LPartial correctionsSedion3.2.2.3.7.6.4.4.72.1.112.1.11.3.3Partial additionsSection1.1.1,1.12,2.2.1,3.2.4,62.1,6.3n6.4.1,6.42,6.4.3,11.2.3,11.613.2.1,App1Oct.2008SH(NA)-080544ENG-KCompatible with GT Designer2 Version 2.90U.Partial correctionsedtion1.1.3,2.1,2.3.1,3.3.1,4.4.1,5.5.6.3,7.3,8.3,9.3.10.3.11.1,113.1,11.3.4,11.4.1,11.4.3,11.6,12.313.1,13.3.1,13.5.1,13.5.2,13.6.1,13.6.3.13.7.1+13.7.3Partial additionsSection1.1.1,1.12,2.2.1,3.2.1,3.5.4,4.1,4.2.1,4.3.1,4.4.6,5.1,52.3,5.3,5.4.1,5.4.10,5.4.13,62.1,72.1,8.2.1,9.2.1,10.2.1,102.3,112.1,11.3.2,12.2.3,13.2.1,13.2.2,13.8,13.9,App1Japanese Manual Version SH-080541-NThis manual confers no industrial property rights or any rights of any other kind,nor does it confer any patent licenses.Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which mayoccur as a result of using the contents noted in this manual.A-9INTRODUCTIONThank you for choosing Mitsubishi Graphic Operation Terminal(Mitsubishi GOT).Read this manual and make sure you understand the functions and performance of the GOT thoroughlyin advance to ensure correct use.CONTENTSSAFETY PRECAUTIONS.A-1A-7INTRODUCTION..A-10CONTENTSA-10A-18ABBREVIATIONS AND GENERIC TERMS..A-20How to read this manual........A-241.OVERVIEW1-1to1-121.1 Before Using Each Function1-21.1.1Each function and related manuals .......1-21.1.2Hardware and OS'required for each function............1-41.1.3Outline of procedure to the operation of each function.1-101.1.4Displayable languages for each function.............2.SYSTEM MONITOR2-1to2-562.1 Features2-12.2 Specifications2-62.2.1System configuration.2.2.22.2.3Access range............2.2.4PreCautionS2-142.3 Display2-162.3.1Outline until starting the system monitor..............2-162.4 Operation Procedure Common to the System Monitor Screens2-192.4.1 Functional change menu screen..2-192.4.2Entering monitor devices(specifying monitor stations and devices)..2-202.4.3Key window setting columns and operation procedure...................2-232.4.4 Switching the display format(DEC/HEX)and ment/no-ment display..2-242.4.5Quick test operation of monitor devices..2-262.4.6Changing screens...........2.5 Entry Monitor2-312.5.1Information displayed on the Entry Monitor screen and key functions...-312.5.2Procedure for entry monitor basic operation......2-342.5.3Deleting entry devices2-352.6 Batch Monitor2-362.6.1Information displayed on the Batch Monitor screen and key functions..........................2-362.6.2Procedure for batch monitor basic operation.2-40A-10