4.Operation4.1 Basic operationOperation mode switchoverAt powering on(external operation mode)APUPU Jog operation mode(Example)PU operation modeValue changeF and frequency flicker.(output frequency monitor)Frequency setting has beenwritten and pleted!!MODEOutput currentOutput voltagemonitormonitorSETDisplay theParameter setting modecurrent setting2Value changeParameter and a setting valueflicker alternately.Parameter write is pleted!!MODEParameter clearAll parameterFaults history clearclearInitial value change list[Operation for displaying faults history](Refer to the inverter manual)Past eight faults can be displayed.(The latest fault is ended by".".)When no fault history exists,is displayed.Initial value change list()functions in the inverters manufactured during or after the period shown bythe serial numbers described on page /Although is displayed,parameter copy does not function.(Refertopage 1)44.2 Operation lock(Press [MODE]for a while(2s))Operation using the setting dial and key of the FR-PA07 can be made invalid toprevent parameter change,and unexpected start or frequency setting.Set"10 or 11"in Px:161,then press (MODE)for 2s to make the setting dial and key operation invalid.When the setting dial and key operation is made invalid,L appears on the operation panel.When the setting dial and key operation is invalid,appears if the setting dial or keyoperation is performed.(When the setting dial or key operation is not performed for 2s,the monitordisplay appears.)To make the setting dial and key operation valid again,pressMODEfor 2s.POINTSet "10 or 11"(key lock mode valid)in Pr:161 Frequency setting/key lock operationselection.OperationDisplay1.Screen at powering onThe monitor display appears.A2.PressPUPU indication is lit.to choose the PU operation mode.3.PressMODEto choose the parameter settingmode(The parameter number read previouslyappears.)4.Tumuntil(Pr:161)appears65.PressSET)to read the currently set value"(initial value)appears.6.Tumto change it to the set value"7.PressSETto set0Flicker ..Parameter setting plete!!8.PressMODEfor 2s to show the monitor mode.MODEPress for 2s.Functions valid even in theoperation lock statusStop and reset withNoteRelease the operation lock to release the PU stop by key operation.54.3 Use the setting dial like a potentiometer to perform operationPOINTSet "1"(setting dial potentiometer mode)in Pr:161 Frequency setting/key lockoperation selection.Changing exampleChanging the frequency from OHz to 60Hz during operationOperation-Display1.Screen at powering onThe monitor display appears.2.PressPU indication is lit.EXTto choose the PU operationPUEXTmode.A3.Change the Pr:16/setting to"1".(Refer to page 5 for change of the setting.)Press(MODE)twice to retum the monitor to frequency monitor4.PressFWDREVto start the inverterAREVappears.The flickering frequency is theYou need not pressSETThe frequency flickers for about 5s.REMARKSIf flickering "60.00"turns to "0.00",the Pr:161 Frequency setting/key lock operationselection setting may not be "1".Independently of whether the inverter is running or at a stop,the frequency can be set bymerely turning the(Use Pr.295 Magnitude of frequency change setting to change thefrequency setting increments of65.Specifications5.1 Standard specificationsItemSpecificationsAmbient temperature-10C to +50C (non-freezing)Ambient humidity90%RH or less(non-condensing)Storage temperatureAmbienceIndoors (free from corrosive gas,flammable gas,oil mist,dust and dirt)Altitude,vibrationMaximum 1000m above sea level for standard operation.5.9m/s2or lessPower supplyPower is supplied from the inverter.Connection methodConnection using the parameter unit connection cable (FR-CB20D)5.2 Outline drawing and panel cutting drawing6822AREVFWDMODESET592-M3 screw7