(2)Test operation and adjustmentACAUTIONBefore starting operation,confirm and adjust the parameters.A failure to do somay cause some machines to make unexpected motions.(3)UsageAWARNING.Thekey is only valid when function setting has been made.Provide anemergency stop switch separately.Make sure that the start signal is off before resetting the alarm.A failure to do somay restart the motor suddenly.Do not modify the equipment.A CAUTIONWhen parameter clear or all parameter clear is performed,each parameterretums to the factory setting.Re-set the required parameters before startingoperation.(4)Corrective actions for alarmACAUTIONProvide safety backup devices,such as an emergency brake,to protectmachines and equipment from hazard if the parameter unit(FR-PU04)beesfaulty.(5)DisposalACAUTIONTreat as industrial waste.(6)General instructionAll illustrations given in this manual may have been drawn with covers or safetyguards removed to provide in-depth description.Before starting operation of theproduct,always retum the covers and guards into original positions as specifiedand operate the equipment in accordance with the manual.A-3CONTENTS-1 PRE-OPERATION INFORMATION1.1 Overview.…1.1.1 Appearance and parts identification....1.1.2 Explanation of the keys................11.2 Installation and Removal...3(2)Using the connection cable (FR-CB2)for connection.......4S500 (NAGEC-CH (F500J-CH(C500)4(2)Removal when the connection cable(FR-CB2)is used ......41.3 Parameters to Be Checked First..................51.3.1 PU display language selection (Pr.145)51.3.2 PU buzzer control (Pr.990).......................51.3.3 PU contrast adjustment (Pr.991).............52 FUNCTIONS62.1 Monitoring Function.2.1.1 Display overview6(1)Main monitor.....6(2)PU level meter A500 F500F500JCH(C500.6(3)Rotation direction monitoring6(4)Operating status indication....6(5)Operation mode indication....(6)Unit indication............7(7)Alarm indication ................2.1.2 Using the SHIFT key to change the main screen......2.1.3 Setting the first priority screen (first screen)...............................82.1.4 Using the HELP key to change the main screen(A500(F5002.1.5 Using the "PU main display data selection parameter"to change the screen.....102.2 Frequency Setting..............112.2.1 Direct setting112.2.2 Step setting ....112.2.3 Precautions for frequency setting..........122.3 Setting and Changing the Parameter Values.132.3.1 Direct setting ..............132.3.2 Step setting.......142.3.3 Function-by-function parameter setting (A500F500 (E500 -NACEC-CH1516(1)Confirmation2.3.5 Precautions for setting write...182.4 Calibration of the Meter (Frequency Meter).......................................2.4.1 Calibration of the FM terminal A500 F500 E500(NAEC)CH192.5 Adjustment of the frequency setting signals "bias"and "gain"................................23(1)Adjust only the bias and gain frequencies and not adjust the voltage24(2)Any point is adjusted with a voltage applied across terminals 2-5.........................26(3)Any point is adjusted without a voltage applied across terminals 2-5......................282.6 Copy and Verify Functions.302.6.1 Copying the parameter settings.302.6.2 Verifying the parameters..313 HELP323.1 Overview of the Help Functions................323.1.1 Help function menu..323.1.2 Help function display data.......333.2 Operation Procedures for the Help Functions......................363.2.1 Monitor function................363.2.2 Selection of PU operation(direct input).3839(1)Calling from the help function menu........39(2)Calling the key operation guide directly..393.2.4 Parameters...…4041(3)Display of "4 Def.Pr.List"(A500 F500E500 (NACEC)CH).42(4)Display of "5 Def.Pr.List 2"A500F500E500(-NAEC-CHS500(NAEC(CH(F500J(CH(C50042433.2.6 Alarm History.…443.2.7Al归rm Clear…453.2.8 Inverter Reset...46F500J(CH(C50047(1)Troubleshooting guidance48F500J(CH(C500)51523.3 Other Precautions....................533.3.1 Precautions for parameter unit operation................53(1)Precautions for the digit count and decimal point of input value.....(2)Other indications.............53(3)Power-on indication....4 OPERATION544.1 Operation M0des.…544.1.1 How to select the operation mode......5.4(1)Switching from external operation mode [EXT]to PU operation mode [PU]...................5.4(2)Switching from PU operation mode [PU]to extemal operation mode [EXT]........................5.4(3)Switching to the external PU bined operation mode.......................54564.2.1 Ordinary operation...........56574.3 Combined Operation (Operation using external input signals and PU).....................584.3.1 Entering the start signal from outside and setting the running frequency from thePU(Pr.79=3)…584.3.2 Entering the running frequency from outside and making start and stop from thePU(Pr.79=4)..594.3.3 Entering the start signal and multi-speed signal from outside and setting multiplespeeds from the PU605 SPECIFICATION61615.1.1 Standard specifications.............615.1.3 Panel cutting drawing....62IVCHAPTER 1PRE-OPERATIONINFORMATIONThis chapter provides the basic "pre-operation information(overview)"for use of this product.Always read the instructions before using the equipment1.1 Overview...........1.2 Installation and Removal.........3Chapter 11.3 Parameters to Be Checked First............................5.The FR-PU04 can be used with the Mitsubishi transistorizedinverters.However,there are restrictions on some functionsChapter 2depending on the model.Note that the following representations are used in thismanual.Chapter 3A500F500E500 NA EC CH、UsableUnusable Unusable UsableUsable UnusableChapter 4Chapter51.1 OverviewPRE-OPERATION INFORMATION1.1.1 Appearance and parts identificationUnpack the parameter unit from the carton,check the name plate on the back,andmake sure that the product has not been damaged before using the equipment.-Monitor sectionWide liquid crystal screen(13 characters x4 lines,with backlight)Interactive parameter settingFR-PU04P ETER UNTHelp function,troubleshootingguidance.O21 different monitor dataConnectorMonitor mode(frequency,current,power,etc.)selection keyOperation mode selection keySetting modeselection keyEscape keyHelp modeFrequency changing keys-Modelselection keyOperation mand keysShift key-●Keys used to mandforward rotation,reverseFunction androtation and stop (reset atnumber keysalarm occurrence).(0to9)Write,read keys1.1.2 Explanation of the keysKeyDescriptionSET keyUsed to select the parameter setting mode.Used to display the main monitor.Operation cancel key.Used to select the help mode.Used to shift to the next item in the setting or monitoring mode.Number keys(Oto(⑨)Used to enter a frequency,parameter number or set value.EXT keyUsed to select the external operation mode.PU keyUsed to select the PU operation mode.Used to keep on increasing or decreasing the runningfrequency.Hold down to vary the frequency.Press either of these keys on the setting mode screen to changethe parameter setting sequentially.On the monitoring,parameter or help menu screen,these keysand keysare used to move the cursor.Hold down the SHIFD key and press either of these keys toadvance or return the display screen one page.In the parameter copy or verify mode,the key is used as averify key.Forward rotation mand key.REV keyReverse rotation mand key.·Stop mand key.Used as a reset key when an alarm occurs.PRE-OPERATION INFORMATIONKeyDescriptionUsed to write a set value in the setting mode.Used as a clear key in the all parameter clear or alarm history clearmode.Used also as a decimal point key.Used as a parameter number read key in the setting mode.Used as an item select key on the menu screen such as parameter list品keyor monitoring list.Used as an alarm definition display key in the alarm history displaymode.Used as a mand voltage read key in the calibration mode.13 character x 4 line liquid crystal display screen shows monitoringDisplaydata,such as frequency,motor current and l/O terminal states,as wellas troubleshooting guidance and other information.Used for connection of the parameter unit with the inverter.You mayConnectoreither connect the unit directly or use the connection cable (FR-CB2for connection.FR-PU04ModelMITSUBISHI ELECTRIC CORPORATIONMADE IN JAPANCAUTION1.Do not use a sharp-pointed tool to push the keys.2.The display is a liquid crystal display.Do not press your fingers against the display.1.2 Installation and RemovalPRE-OPERATION INFORMATIONTo ensure safety,install and remove the parameter unit after switching the power off.1.2.1 Installation(1)Installation to the inverterA500F500E500 (NAECCH S500 NAECCH F500J CH(C5001)Remove the operation panel(FR-DU04)and accessory cover.2)Insert the parameter unit straight and fit it securely(2)Using the connection cable (FR-CB2)for connectionREMARKSFor details of the connection cable(FR-CB2),refer to the connection cable (FR-CB2)instruction manual.When connecting to the FR-A500/F500/E500 series.1)Remove the operation panel.2)Insert the cable plugs securely into the connectors of the inverter andparameter unit (FR-PU04)along the cable guides until the stoppers areactuated.Joint connectorabTababFR-A500/F500 series.FR-E500 series.CAUTIONInstall the operation panel only when the front cover is installed.3