Table of contentsBSH4.1534.2Electromagic patibility,EMC...............534.3554.4Mounting the motor.................584.4.1Installation and connection of IP67 kit(accessory).604.5Electrical installation...........................614.5.1Connectors and connector assignments.........614.5.2654.5.3Holding brake connection....................715 Commissioning......................................736 Diagnostics and troubleshooting.......................756.1Diagnostics and troubleshooting.................756.1.1756.1.2757 Accessories and spare parts ..........................777.1777.2777.3787.3.1Motor cables1.5mm2.................787.3.2Motor cables 2.5 mm2.......................797.3.3807.4818 Service,maintenance and disposal.....................838.1Service address..............................838.2Storage.....................................838.3Maintenance.................................838.4858.5Shipping,storage,disposal......................854Servo motorBSHTable of contents9Glossary.…879.1Units and conversion tables ....................879.1.1879.1.2MaSS.....................................879.1.3879.1.4PoWer....................................879.1.589.1.6889.1.7Moment of inertia...........................889.1.8Temperature.........889.1.9Conductor cross section......................889.210Index..............................................Servo motor5Table of contentsBSH6Servo motorBSHAbout this manualAbout this manualThis manual is valid for BSH standard products.Chapter 1 "Introduction"lists the type code for this product.The type code allows you to identifywhether your product is a standard product or a customized version.Source manualsThe latest versions of the manuals can be downloaded from the Interat:://www.schneider-electric.Corrections and suggestions We always try to further optimize our manuals.We wele your sug-gestions and corrections.Please get in touch with us by e-mail:techm @schneider-electric..Work steps If work steps must be performed consecutively,this sequence of stepsis represented as follows:Special prerequisites for the following work stepsStep 1Specific response to this work stepStep 2If a response to a work step is indicated,this allows you to verify that thework step has been performed correctly.Unless otherwise stated,the individual steps must be performed in thespecified sequence.Making work easierInformation on making work easier is highlighted by this symbol:Sections highlighted this way provide supplementarySI units are the original values.Converted units are shown in bracketsbehind the original value;they may be rounded.Example:Minimum conductor cross section:1.5 mm-(AWG 14)Glossary Explanations of special technical terms and abbreviations.Index List of keywords with references to the corresponding page numbers.Servo motor7About this manualBSH8Servo motorBSH1 Introduction1.3NameplateThe nameplate contains the following data:BSH0000000000001D-N000000000000000000000000Imax0.00Armsdd.mm.yyyy0.00AmsNmax0000rpmThermo PTC-nN0000rpm1P40(65)-Made in GermanyUbrOVdc-UN-PNPbrTh-CI F DT-F2UsE198273Mbr ONm.Figure 1.1Nameplate(1)Motor type,see type codeOrder no.Continuous stall torqueContinuous stall current(5)Nominal speed of rotation(6)Maximum nominal value of supply voltageNominal power(8)Thermal classUL logo and assigned UL number(10)Maximum current(11)Serial number(12)Date of manufacture(13)Maximum speed of rotation(14)Temperature sensor(15)Degree of protection(16)(17)Nominal power (electrical pull-in power)holding brake(18)Holding torque holding brake(19)CE mark(20)BarcodeServo motor111 IntroductionBSH1.4Type codeBSH 070 1 P 0Product family:Synchronous motor-low inertiaSize (housing)055 55 mm flange070 70 mm flange100 =100 mm flange140140 mm flange205 205 mm flangeLength1 =1 stack2=2 stacks3=3 stacks4 =4 stacksWindingN=Optimized in terms of torqueP=Optimized in terms of torque and speed of rotationT Optimized in terms of high speed of rotationShaft and degree of protection0=Smooth shaft;degree of protection:shaft IP54 1),housing IP653=Parallel key;degree of protection:shaft and housing IP 652)Encoder system1 Absolute singleturn 128 Sin/Cos periods per revolution (SKS36)2 Absolute multiturn 128 Sin/Cos periods per revolution (SKM36)Holding brakeA=Without holding brakeF=With holding brakeConnection version1 Straight connector2=Angular connector9o°，can be rotated3 Terminal box for power and holding brake,90 angle connector forencoder,can be rotatedMechanical interface-mountingA=International IEC Standard (at motor flange)P=International IEC standard (at motor flange),BSH1402T,BSH1403T and BSH1404P with power connector M401)In the case of mounting position IM V3(drive shaft vertical,shaft end up),the motor only has degree of protection IP50.2)The maximum permissible speed is limited to 6000 min by the shaft sealing ring.If you have questions conceming the type code,contact your SchneiderElectric sales office.12Servo motor