Chapter 4 Installation and Wiring4.1 Installation…4.2 Wiring Precautions.4-74.2.1 Connecting the Power Cord..4-74.2.2 Connecting the Power Supply..4-124.2.3 Grounding…4.2.4 1/O Signal Line Placement..............4-144.3 CF Card Insertion/Removal..............4-144.3.1 Inserting the CF Card...........4-154.3.2 Removing the CF Card..............4-154.3.3 CF Card Handling...............4.4 USB Cable Clamp Attachment/Removal4-164.4.1XBT0T2110/2210 Series.....4-164.4.2XBT0T4320 Series.4-174.4.3XBT0T5220/5320 Series....4-18Chapter 5 Maintenance5.1 Cleaning the Display......................5-25.2 Periodic Check Points....5.3 Replacing the Installation Gasket.................................5-35.4 Replacing the Backlight................5-42Safety InstructionsRead these instructions carefully,and look at the equipment to bee familiar with the device before tryingto install,operate,or maintain it.The following special messages may appear throughout this documentationor on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifiesa procedure.The addition of this symbol to a Danger or Warning safety label indicatesthat an electrical hazard exists,which will result in personal injury if theinstructions are not followed.This is the safety alert symbol.It is used to alert you to potential personalinjury hazards.Obey all safety messages that follow this symbol to avoidpossible injury or deathA DANGERDANGER indicates an imminently hazardous situation.which.will result in deathor serious injury.A WARNINGWARNING indicates a potentially hazardous situation,which,if not avoided,can resultin death,serious injury,or equipment damage.A CAUTIONCAUTION indicates a potentially hazardous situation,which,if not avoided,can resultin injury or equipment damage.DisclaimerElectrical equipment should be installed,operated,serviced,and maintained only by qualified personnel.Noresponsibility is assumed by Schneider Electric for any consequences arising out ofthe use of this material.Thisdocument is not intended as an instruction manual for untrained persons.3Information SymbolsThis manual uses the following icons:Screen EditorIndicates the Vijeo Designer software.PLCAbbreviation for Programmable Logic Controller.IMPORTANTIndicates useful or important supplemental information.NOTEContains additional or useful information.SEE→Indicates pages containing related information.4Handling the LCD PanelThe following characteristics are specific to the LCD unit and are considered normal behavior:LCD screen may show unevenness in the brightness of certain images or may appear different when seenfrom outside the specified viewing angle.Extended shadows,or crosstalk may also appear on the sides ofscreen images.LCD screen pixels may contain black and white colored spots and color display may seem to havechanged.When the same image is displayed on the unit's screen for a long period,an afterimage may appear whenthe image is changed.If this happens,tum OFF the unit,wait 10 sec.and then restart the unit.NOTEChange the screen image periodically and try not to display the same image for a longperiod of time.A WARNINGSERIOUS EYE AND SKIN INJURY FROM DAMAGED OR LEAKING LCD PANELDo not touch nor handle a unit whose LCD panel appears damaged or seems to be leaking.Do not use sharp objects or tools in the vicinity of the LCD touch panel or to operate itsbuttons.Handle the LCD panel carefully to prevent puncture,bursting,or cracking of the panel material.The LCD panel's liquid contains an irritant.If the panel is damaged and any of this liquid is incontact with your skin,immediately rinse the area with running water for at least 15 min.If theliquid gets in your eyes,immediately rinse your eyes with running water for at least 15 min.andconsult a doctor.Failure to follow these instructions can result in death,serious injury,or equipment damage.A WARNINGRISK OF BURNS OR EQUIPMENT DAMAGEWait at least 10 sec.before restoring power to the HMI unit after turning it off.Switching the unit offand on too quickly can result in overheating that leads to personnel burn hazards or equipmentdamage.Failure to follow these instructions can result in death,serious injury,or equipment damage.5XBT OT Series Models and FeaturesThe XBT OT series refers to the following model numbers:ModelXBT OT2110XBT OT2210XBT OT4320XBT OT5220XBT OT5320CPULH7A404LH7A404LH7A404LH7A404LH7A404VxWorksVxWorksVxWorksVxWorksVxWorksDRAM32MB32MB32MB32MB32MBMain Flash32MB32MB32MB32MB32MBSRAM512K512K512K512K512KPanel Size5.77.5”10.4”ResolutionQVGAQVGAVGAVGAVGADisplay DeviceBlue LCDSTNTFTTFTTFTColor8 gray scale256 colors256 colors16 colors256 colorsBrightness8 levels8 levels8 levels8levels8 levelsContrast8 levels8 levelsn/an/an/aCOM1RS232CRS232CRS232CRS232CRS232CCOM2RS422/485RS422/485RS422/485RS422/485RS422485USBYes(1)Yes(1)Yes(1)Yes(1)Yes(1)EtherNoNoNoNoNoCF Card SlotNoNoYesYesYesAuxiliaryNoNoNoNoNoSound OutNoNoNoNoNoSound InNoNoNoNoNoVideoNoNoNoNoNo6A WARNINGLOSS OF CONTROLThe designer of any control scheme must consider the potential failure modes of control pathsand,for certain critical control functions,provide a means to achieve a safe state during andafter a path failure.Examples of critical control functions are emergency stop and overtravelstop.Separate or redundant control paths must be provided for critical control functions.System control paths may include munication links.Consideration must be given to theimplications of unanticipated transmission delays or failures of the link.1Each implementation of the Magelis XBT OT must be individually and thoroughly tested forproper operation before being placed into service.The machine control system design shouldtake into account the possibility of the backlight failing and the operator being unable to controlthe machine,or making errors in the control of the machineFailure to follow these instructions can result in death,serious injury,or equipment damage.1For additional information,refer to NEMA ICS 1.1 (latest edition),"Safety Guidelines for the Application,Installation,and Maintenance of Solid State Control".Do not use the unit as the only means ofcontrol for critical system functions such as motor start/stop or powerdisconnect.Do not use the unit as the only notification device for critical alarms,such as device overheating orovercurrent.Do not use the unit with aircraft control devices,aerospace equipment,central trunk data transmission(munication)devices,nuclear power control devices,or medical life support equipment,due to thereliability requirements of these industries.In the event of backlight or other unit failure,it may be difficult or impossible to identify a function.Emergency stop,fuel shutoff,or any function that may present a danger if not immediately executed must beprovided independently of the unit.In addition,the machine control system design should take into accountthe possibility of the backlight failing and the operator being unable to control the machine,or making errorsin the control of the machine.7Package ContentsThe following items are included in the OT unit's package.Before using the OT,please check that items listed are present.OT Unit:1Quick Start GuideWaming/Caution InformationQuick StartWarning/GuideCautionInstallation Gasket:1(Attached to the OT unit)Installation Fasteners:4 per setDC Power Connector:1OT2110/2210/4320 seriesOT5220/5320 series(Attached to the OT unit(Attached to the OT unit)for OT2110/2210 series)USB Cable Clamp:1 setOT2110/2210 seriesHolder.1,Clamp:1OT4320 seriesHolder.1,Cover:1OT5220/5320 seriesHolder.1,Clamp:1This unit has been carefully packed,with special attention to quality.However,should you find anything damaged ormissing,please contact Schneider Electric immediately.8UL/c-UL ApprovalThe following units are UL/c-UL listed products.(UL File No.E220851)Product Model No.UU/c-UL Registration Model No.XBT OT21103580207-02XBT OT22103580207-01XBT OT43203580206-01XBT OT52203520208-02XBT OT53203520208-02This product conforms to the following standards:·UL508Industrial Control EquipmentCSA-C22.2 No.142-M1987 (c-UL Approval)Standard for Process Control EquipmentA CAUTIONEQUIPMENT DAMAGEThe OT unit's rear face is not approved as an enclosure.When building the OT unit into an end-use product,be sure to use an enclosure that satisfies UL508 and CSA-C22.2 No.142-M1987standards as the end-use product's overall enclosure.The OT unit must be used indoors only.Install and operate the OT with its front panel facing outwards.If the OT is mounted so as to cool itself naturally,be sure to install it in a vertical panel.Also,itis remended that the OT should be mounted at least 100mm [3.94in]away from any otheradjacent structures or machine parts.The temperature must be checked on the final product inwhich the OT is installed.Serial Interface (COM2)is not a Limited Power Source.For use on a flat surface of a Type 4X(Indoor Use Only)and/or Type 13 Enclosure.Failure to follow these instructions can result in injury or equipment damage.9CE MarkingThe following units are CE marked products plying with the EMC Directive.They ply with EN55011 Class A,EN61131-2XBT OT2110XBT OT2210XBT OT4320XBT OT5220XBT OT532010