ENGLISH35013589112006SafetySafety InstructionsRead these instructions carefully,and look at the equipment to bee familiar with thedevice before trying to install,operate,or maintain it.The following special messages mayappear throughout this documentation or on the equipment to warn of potential hazards orto call attention to information that clarifies or simplifies a procedure.The addition of this symbol to a Danger or Warning safety labelindicates that an electrical hazard exists,which will result in personalinjury if the instructions are not followed.This is the safety alert symbol.It is used to alert you to potentialpersonal injury hazards.Obey all safety messages that follow thissymbol to avoid possible injury or death.DANGERDANGER indicates a hazardous situation,which will result in death orserious injury.A WARNINGWARNING indicates a potentially hazardous situation which,if not avoided,can result in death,serious injury,or equipment damage.A CAUTIONCAUTION indicates a potentially hazardous situation,which,if not avoided,can result in personal injury or equipment damage.DISCLAIMERElectrical equipment should be serviced only by qualified personnel.No responsibility isassumed by Schneider Electric for any consequences arising out of the use of thismaterial.This document is not intended as an instruction manual for untrained persons.2006 Schneider Electric.All Rights Reserved.3501358911/20063Safety(cont'd)Essential Safety PrecautionsA WARNINGRISK OF EXPLOSIONDo not use this unit in an environment where flammable gases are present,since operating this unit may cause an explosion.Failure to follow this instruction can result in death,serious injury,orequipment damage.A CAUTIONENVIRONMENTAL EXPOSURE HAZARDDo not allow liquids,metal or charged particles to enter this unit,since theycan cause a malfunction.Do not use or store this unit in direct sunlight,in excessively dusty or dirtyenvironments or where excessive impact or vibration can occur.Failure to follow this instruction can result in injury or equipmentdamage.Schneider Electric has designed the USB Modbus Plus Communication Adapter for use inNon-Hazardous locations only (UL508).43501358911/2006IntroductionUSB Modbus Plus Communication Adapter-OverviewThank you for purchasing TELEMECANIQUE XBTZGUMP Modbus Plus USB gateway forXBT GT.This unit is designed to provide a bridge between an USB connection and aModbus Plus Network.It es as an accessory to the XBT GT terminals.Package ContentsPlease check that the following items are included in your package:TSXCUSBMBP USB Modbus Plus CommunicationAdapterInstallation Guide(this guide)Fixing SupportFixing Accessory AX2-DL02 for DIN rail4 Attachment Screws CBL ZS M4x16PPAdhesive Transfer Tape 3M 468 MP3501358911/20065Introduction(cont'd)CE MarkingThe XBTZGUMP is a CE marked,EMC pliant product.This unit conform to EN55011 Class A and EN61000-6-2 directives.For detailed CE marking information,please contact your local distributor.Compatible ModelsThe following XBT GT Series units are patible with the XBTZGUMP Modbus Plus USBgateway because they have a USB port:O XBT GT Series·XBT GT:2··XBT GT4。·XBT GT5··XBT GT6··XBT GT7·63501358911/2006General SpecificationsExternal DrawingsThe following diagrams show external drawings of the TSXCUSBMBP and its dimensions.O Example 1:Case of mounting on a DIN rail in a horizontal positionmm14461.8inch5.672.43933.6646.31.8254.3214(7.5)DIN RAIL(0.29)DIN RAILO Example 2:Case of mounting on a DIN rail in a vertical positionmm9361.8inch3.662.431445.6746.31.8254.32.14(7.5)DIN RAIL(0.29)DIN RAIL3501358911/2006General Specifications(cont'd)ElectricalDescriptionRated VoltageDC 5 V(supplied from the XBT GT)Power Consumption2.5 Wor lessEnvironmentalItemDescriptionAmbient Operating Temperature0°Cto+50°C(+122F日)Ambient Humidity10%RH to 70%RH(No condensing)StructuralThe following table gives the weight and external dimensions of TSXCUSBMBP USBModbus Plus Communication Adapter,fixing support,fixing accessory AX2-DL02 for DINrail and adhesive transfer tape 3M 468 MP.ElementWeightExternal DimensionsUSB Modbus PlusCommunication186 g(0.41 Ib)or lessW140mm(5.50in.)xH91.5mm(3.60in.)AdapterxD28.6mm(1.13in.)Fixing support72g(0.16 lb)or lessW144mm(5.67in.)xH92.9mm(3.66in.)xD46.3mm(1.82in.)Fixing accessoryAX2-DL0270 g (0.15 Ib)or lessW65mm(2.56in.)xH49mm(1.93in.)xfor DIN railD13.5mm(0.531in.)Adhesive transferW135mm(5.31in.)xH60mm(2.36in.)xtape 3M 468 MPD0.125mm(0.00492in.)83501358911/2006Attachment methodsAttachment methodsThree different attachment methods can be used.O Screwing the fixing support to a wall or gridStep 1:Place the fixing support on the wall or the grid in a vertical or horizontal direction.Use 4attachment screws,the heads of which should be less than 6 mm(0.24 in)in height.You can use the 4 screws supplied with the package:mm6 pans wrench:3 on flatsinch0.12 on flats☑60.244 screws CBL ZS M4 x 6M0.16x0.24Step 2:Insert the TSXCUSBMBP in the fixing supportNote:Please insert/remove the TSXCUSBMBP in/from the fixing support carrefully in thehorizontal direction.Otherwise this may affect mechanical performance of the fixing support.3501358911/2006Attachment methods(cont'd)O Bonding the fixing support to a wallAdhesive Application Remendation:The ideal application temperature is between 21 C (69.8 F)and 38 C(100.4 F).Application on surfaces whose temperature is less than 10 C(50 F)is notremended because the adhesive would bee too hard to enable adhesion.For maximum bond strength the wall surface should be pletely clean and dry.Typical cleaning solvents are heptane(for oily surfaces)or isopropyl alcohol forplastics.Use reagent grade solvents since mon household materials likerubbing alcohol frequently contain oils to minimize the drying affect on skin and caninterfere with the performance of a pressure-sensitive adhesive.Carefully read andfollow the manufacturer's precautions and directions for use when working withsolvents.These cleaning remendations may not be in pliance with the rulesof certain air quality management districts in California;consult applicable rulesbefore use.Step 1:Insert the TSXCUSBMBP in the fixing support.Note:Please insert/remove the TSXCUSBMBP in/from the fixing support carrefully in thehorizontal direction.Otherwise this may affect mechanical performance of the fixing support.Step 2:Bond the adhesive transfer tape 3M 468 MP included with the package contents tothe fixing support.Apply pressure to enable the adhesive to e into direct contact withthe surface.Step 3:Remove the protective paper from the adhesive transfer tape 3M 468 MP.Step 4:Bond the fixing support onto the wall in a vertical or horizontal direction.For example,when placed horizontally:Adhesive transfer tape3M 468 MP103501358911/2006