OperationOperating the Profibus DP Slave Unit..23System Configuration.......4When Using Screen Creation Software.........24TroubleshootingNo Data Communication252Safety InstructionsSafety InstructionsRead these instructions carefully,and look at the equipment to beefamiliar with the device before trying to install,operate,or maintain it.Thefollowing special messages may appear throughout this documentation or onthe equipment to warn of potential hazards or to call attention to informationthat clarifies or simplifies a procedure.The addition of this symbol to a Danger or Warning safetylabel indicates that an electrical hazard exists,which willresult in personal injury if the instructions are not followed.This is the safety alert symbol.It is used to alert you topotential personal injury hazards.Obey all safetymessages that follow this symbol to avoid possibleinjury or death.DANGERDANGER indicates an imminently hazardous situation which,ifnot avoided will result in death or serious injury.WARNINGWARNING indicates a potentially hazardous situation which,ifnot avoided,can result in death,serious injury,or equipmentdamage.A CAUTIONCAUTION indicates a potentially hazardous situation,which,ifnot avoided,can result in personal injury or equipment damage.3DISCLAIMERElectrical equipment should be installed,operated,serviced andmaintained only by qualified personnel.No responsibility isassumed by Schneider Electric for any consequences arising out ofthe use of this material.2006 Schneider Electric.All Rights Reserved.4StandardsPresentationThe Profibus DP Slave unit XBTZGPDP is a UL/c-UL listed (UL File NoE182139,UL File No.E220851).This product conforms to the following standards:·UL508Industrial Control Equipment.Standard for Electrical Equipment for using in Class I and Class Il,Division 2and Class Ill,Hazardous (Classified)Locations.CAN/CSA-C22.2,No.14-95M (c-UL Listed)Industrial Control Equipment.CAN/CSA-C22.2,No.213-M1987(c-UL Listed)Non-incendive Electrical Equipment for use in Class I,Division 2 HazardousLocations.5UL 1604/CSA-C22.2 No.213-Compliance and HandlingCautionsDANGERRISK OF EXPLOSIONPower,input and output(1/O)wiring must be in accordance withClass I,Division 2 wiring methods-Article 501-4(b)of theNational Electrical Code,NFPA 70 within the United States andin accordance with section 18-152 of the Canadian ElectricalCode for units installed within Canada.Suitable for use in Class I,Division 2,Groups A,B,C and DHazardous Locations or Non-Hazardous Locations,Do not perform substitution of ponents that may impairpliance to Class I,Division 2.Confirm that the location is not subject to any risk of explosionbefore connecting or disconnecting equipment,replacing orwiring modules.Confirm that the power supply has been turned OFF beforedisconnecting equipment,replacing or wiring modules,orconfirm that the location is not subject to the risk of explosion.This unit must only be mounted in this manufacturer's UL listedClass 1,Division 2,Groups A,B,C and D panels.Failure to follow this instruction will result in death orserious injury.6StandardsA CAUTIONRISK OF EQUIPMENT DAMAGEThe XBT GT unit's rear face is not approved as an enclosure.When building the XBT GT unit into an end-user product,besure to use an enclosure that satisfies the standards as the end-use product's overall enclosure.The XBT GT unit must be used indoors only.Install and operate the XBT GT unit with its front panel facingoutwards.If the XBT GT is mounted so as to cool itself naturally,install itin a vertical panel.It is remended that the XBT GT unitshould be mounted at least 100 mm(3.94 in.)away from anyother adjacent structures or machine parts.The temperaturemust be checked on the final product in which the XBT GT unitis installed.Failure to follow this instruction can result in injury orequipment damage.CE MarkingThe profibus DP Slave unit is a CE marked product that conforms to EMCdirectives.EN55011 Class A and EN61000-6-2.For detailed CE marking information,please ask your local Profibus DP Slaveunit distributor.CE Marking regulations requires the attachment of a Ferrite core(included)tothe Profibus cable being used.7EnglishOverviewSpecificationsDetailed below the are specifications and dimensions of the Profibus DPSlave unit.Electrical SpecificationsItemsSpecificationsRated Voltage5 VDC +/-5 %(supplied by the XBT GT unit)Power ConsumptionLess than 2.4 WVoltage Endurance500 VAC 20 mA for 1 minuteInsulation ResistanceMore than 500 VDC 100 MEnvironmental SpecificationsItemsSpecificationsOperating Temperature0C..+50°C(32℉..122F)Storage Temperature-20C..+60℃(-4°℉..140°F)Ambient Humidity10%..90%RH(Wet bulb temperature:39 C(102.2 F)max.-no condensationStorage Humidity10%..90%RH(Wet bulb temperature:39 C(102.2 F)max.-no condensationDustLess than 0.1 mg/m3No electrically conductive dusty conditionsAtmosphereFree of corrosive gas.Pollution DegreePollution Degree 29ItemsSpecificationsAtmosphere(Altitude)800..1114hPa(Height:at an altitude of less than 2000 m(6,562Ft)Vibration ResistanceComplies with JIS B 3502,IEC 61131-2When vibration is not continuous:10.57Hz0.075mm57.150Hz9.8m/s2When vibration is continuous:10.57Hz0.035mm57.150Hz4.9m/s210...25 Hz X,Y,Z directions for 10 times(80min.)Impact ResistanceComplies with JIS B 3502.IEC61131-2(147 m/s2 to twice X,Y,Z each direction)Noise Immunity (viaNoise Voltage:1200 Vp-pnoise simulatorPulse Duration:1 usRise Time:1 nsElectrostatic DischargeContact Electrical Discharge 6 kV(plies withIEC 61000-4-2 Level3)Structural SpecificationItemSpecificationsInstallation MethodScrew fixingCooling MethodNatural air coolingWeightApprox 500 g (1.1 /b)External DimensionsW88.2mm(3.47in.)xH91mm(3.58in.)×D21.1 mm(0.83 in.)(excluding protection andconnector parts)10