2.Before you beginRead and understand these instructions before performing any procedure with this drive.A DANGERHAZARDOUS VOLTAGERead and understand the Installation Manual before installing or operating the Altivar 61 drive.Installation,adjustment,repair,and maintenance must be performed by qualified personnel.The user is responsible for pliance with all intemational and national electrical standards in force concerningprotective grounding of all equipment.Many parts of this variable speed drive,including the printed circuit cards,operate at the line voltage.DO NOT TOUCH.Use only electrically insulated tools.DO NOT touch unshielded ponents or terminal strip screw connections with voltage present.DO NOT short across terminals PA and PC or across the DC bus capacitors.Install and close all the covers before applying power or starting and stopping the drive.Before servicing the variable speed driveDisconnect all power.Place a DO NOT TURN ON"label on the variable speed drive disconnect.Lock the disconnect in the open position.Disconnect all power including external control power that may be present before servicing the drive.WAIT 15MINUTES to allow the DC bus capacitors to discharge.Then follow the DC bus voltage measurement procedure givenin the Installation Manual to verify that the DC voltage is less than 45 VDC.The drive LEDs are not accurate indicatorsof the absence of DC bus voltage.Electric shock will result in death or serious injury.A CAUTIONDAMAGED EQUIPMENTDo not install or operate any drive that appears damaged.Failure to follow this instruction can result in equipment damage.3.IntroductionThank you for purchasing the Metasys N2 option card (VW3 A3 313)for Altivar 61 drive.By Installing this board into the Altivar 61,data munication can be made with a host puter or other device via Metasys N2 work.The munication card has a Dsub 9-pin connector for connection to the work.Data exchanges give access to all Altivar 61 functions:Control (start,stop,reset,setpoint)..Monitoring (status,current,voltage,thermal state..),Diagnostics (alarms).The graphic display teminal or the integrated display terminal can be used to access numerous functions for munication configurationand diagnostics.54.Documentation structure■Metasys N2 manualThe present Metasys N2 user manual describes:connection to Metasys N2,configuration of the munication-specific parameters via the integrated HMI or the graphic HMI,·diagnostics,·works variables.You will also find important information in other Altivar 61 technical documents.They are available on the Web site www.telemecanique.and on the CDROM delivered with each drive.■Installation manualThe installation manual describes:how to assemble the drive (particularly how to mount the Metasys N2 card),how to connect the drive.■Programming manualThe programming manual describes:the functions and parameters of the drive.how to use the drive HMI (integrated HMI and graphic HMI).Communication parameters manualThe Communication parameters manual describes:the operating modes specific to munication (CiA 402 state chart),the interaction between munication and local control (HMI and terminals).the drive parameters with specific information for use via a munication work (addresses,formats,etc).When using the Metasys N2 card,some sections of the Communication parameters manual are not relevant:profiles,·CiA402 profile.The description of drive parameters is useful only if you use the parameters access function of the Metasys N2 card (MBOXPARAMMBOXVALUEREAD,MBOXVALUEWRITE)or the munication scanner function (COMSCANOUT1,COMSCANIN1).5.NotationDrive terminal displaysThe graphic display terminal menus are shown in square brackets.Example:[1.9 COMMUNICATION].The integrated 7-segment display terminal menus are shown in round brackets with a""at the end.Example:(Cn-).Parameter names displayed on the graphic display terminal are written in square brackets.Example:[Fallback speed]Parameter codes displayed on the integrated 7-segment display terminal are written in round brackets.Example:(L FF).■FormatsHexadecimal values are written as follows:16#or 0xBinary values are written as follows:2#■AbbreviationsO=OptionalM=Mandatory76.Quick startOperationRefer toAHow to realize a factory setting of the driveIn the menu:(1.12 FACTORY SETTINGS][1 DRIVE MENU]1.12 FACTORY SETTINGS]Select IConfig.Sourcel:Macro-conf.Select[PARAMETER GROUP LIST刀：AMIHow to configure main Metasys N2 munication parameters:9.1.Communication parametersIn the menupage_14[1 DRIVE MENU][1.9 COMMUNICATION][MET N2]Check [Address](Metasys N2 MAC address)How to configure control is from Metasys N29.2.Control page 15In the menu:1 DRIVE MENU]1.6 COMMAND]Change [Ref.1 channel]from "Al1"to "Com.card"DHandle the drive by the Metasys N2 controllerControl start stop by the binary value RUNSTOPCMD.Control the velocity setpoint by the analog value INPUTREFControl direction of rotation by the binary value FWDREVCMD,Monitor if the drive is controlled local or remote(Metasys N2)by the binary value HANDAUTOACT.Monitor the running /stopped state by the binary value RUNSTOP,Monitor the actual direction of rotation by the binary value FWDREVMonitor the actual speed or frequency by the analog value OUTPUTSPEED or OUTPUTFREQ.Fault handling:Monitor the fault state by the binary value FAULT,Monitor the fault detail by the analog value LASTFLT.Remote reset the fault by the binary value FAULTRESET.ESwitch local remote by the drive HMIProgramming manualPress F4 key (marked TK)to switch alternately from between Metasys N2 and HMI.Graphic display terminalThe right of the upper display line:REM:control by Metasys N2,·LOC:control by HMI..Diagnose Metasys N2 munication by the drive HMI10.2.Checking theIn the menu:munication page 25[1 DRIVE MENU]COMMUNICATION MAP][DIAG NETWORK]Monitor the frame and error frame counters.GDiagnose Metasys N2 munication by the drive HMI10.2.Checking theIn the menu:munication page 25[1 DRIVE MENU]1.2 MONITORING]COMMUNICATION MAP]Check that the Command Channel is Com.card,Check that Active ref.channel is Com.card.HDisable work fault for testingProgramming manualIn the menu:1.8 FAULT MANAGEMENT]1 DRIVE MENU]FLE-)[1.8 FAULT MANAGEMENT(FL E-)Configure [COM.FAULT MANAGEMENT]to [lgnore].87.Hardware setup7.1.ReceiptCheck that the card reference printed on the label is the same as that on the delivery note corresponding to the purchase order.Remove the option card from its packaging and check that it has not been damaged in transit.7.2.Hardware descriptionLEDsAddress switchesPolarization switchesFemale Dsub 9-pin connector7.3.Installing the card in the driveRefer to the Installation manual.97.Hardware setup7.4.Switch codingChoosing polarizationSet both switches to the lower position.Polarization to the RS 485 line at 4.7 ko.■Coding the addressThe switches are used to encode the address(1 to 254)of the drive on the bus.If address 0 is defined by the switches,the card will use address 1.The usage of the address 255 is not advised.The switch settings can only be changed when the drive is turned off.The correspondence between the value and the position of the switch is as follows:.0=OFF=Switch in upper position,1=ON Switch in lower position.The address is binary-coded.ExamplesAddress11=2#0001011ON+Address110=2#1101110ON108.Connecting to the bus8.1.Cable routing practicesWhen wiring Altivar 61 drives to a Metasys N2 work,follow all wiring practices required by national and local electrical codes.Alsoobserve the following guidelines:Avoid areas of high temperature,moisture,vibration,or other mechanical stress.Secure the cable where necessary to prevent its weight and the weight of other cables from pulling or twisting the cable.Use cable ducts,raceways,or other structures to protect the cable.Use these structures for signal wiring paths.They must not containpower wiring.Avoid sources of electrical interference that can induce noise into the cable.Use the maximum practicable separation from such sourcesWhen planning cable routing within a building,follow these guidelinesMaintain a minimum separation of 1 m from the following equipment:air conditioners and large blowers,elevators and escalators,radios and televisions,inter and security systems,fluorescent,incandescent,and neon lighting fixtures.Maintain a minimum separation of 3 m from the following equipment:line and motor power wiring.·transfomers,·generators,alternators.When wiring in electrical equipment rooms or large electrical equipment line-ups,observe the following guidelines for cable segregationand separation of circuits:Use metallic conduit for drive wiring.Do not run control work and power wiring in the same conduit.Separate non-metallic conduits or cable trays used to camy power wiring from metallic conduit camying low-level control work wiringby at least 300 mm.Separate metallic conduits camying power wiring or low-level control work wiring by at least 80 mm.Cross the metallic conduits and non-metallic conduits at right angles whenever power and control work wiring cross.Attenuate conducted emissions from the drive to the line in some installations to prevent interference with telemunication,radio,andsensitive electronic equipment.Such instances may require attenuating filters.Consult the Altivar catalog for selection and application ofthese filters.Maximum length of bus1000 m at 19,200 bps (9600 bps max.with Metasys N2)Maximum number of stations32 stations,i.e,31 slaves (without repeater)8.2.Card connector pinoutContact no.Signal1Reserved(do not connect)234GroundRxD1 =RD(B)6RxD1 RD(B)8Reserved (do not connect)9You can also use an additional adapter from PHOENIX-CONTACT (SUBCON-PLUS ref:27 61 83 9)to connect the work cable to thecard.Various notation exist for RS485 signals,the table below may be helpful.Metasys N2EIA/TIA-485ModbusJbusUni-TelwayB/B'D1RD+/TD+or L+D(B)RD-/TD-or L-GroundC/C'Common