67TM2AMM3HT.6927Chapter 4 TM2 Expert Modules .........79TM200HSC206 DF and TM200HSC206DT.................79Chapter 5 TM2 Communication Module818183Index .....89E티00000000396 10/2010Safety InformationImportant InformationNOTICERead these instructions carefully,and look at the equipment to bee familiar withthe device before trying to install,operate,or maintain it.The following specialmessages may appear throughout this documentation or on the equipment to warnof potential hazards or to call attention to information that clarifies or simplifies aprocedure.The addition of this symbol to a Danger or Warning safety labelindicates that an electrical hazard exists,which will result in personalinjury if the instructions are not followed.This is the safety alert symbol.It is used to alert you to potentialpersonal injury hazards.Obey all safety messages that follow thissymbol to avoid possible injury or death.A DANGERDANGER indicates an imminently hazardous situation which,if not avoided,will result in death or serious injury.A WARNINGWARNING indicates a potentially hazardous situation which,if not avoided,canresult in death or serious injury.EI0000000039610/20105CAUTIONCAUTION indicates a potentially hazardous situation which,if not avoided,canresult in minor or moderate injury.CAUTIONCAUTION,used without the safety alert symbol,indicates a potentiallyhazardous situation which,if not avoided,can result in equipment damagePLEASE NOTEElectrical equipment should be installed,operated,serviced,and maintained only byqualified personnel.No responsibility is assumed by Schneider Electric for anyconsequences arising out of the use of this material.A qualified person is one who has skills and knowledge related to the constructionand operation of electrical equipment and the installation,and has received safetytraining to recognize and avoid the hazards involved.6E티00000000396 10/2010About the BookAt a GlanceDocument ScopeThis document describes the configuration of the TM2 Input/Output modules.Forfurther information,refer to the separate documents provided in the SoMachineonline help.Validity NoteThis document has been updated with the release of SoMachine V2.0.Related DocumentsTitle of DocumentationReference NumberModicon M238 Logic Controller Programming GuideEIO0000000384(ENG);E00000000385(FRE);E티00000000386(GER);EIO0000000388(SPA);E1O0000000389(CHS)Magelis XBTGC HMI Controller Programming GuideE00000000632 (ENG);E00000000633 (FRE);EIO0000000634(GER):E티00000000635(SPA);E00000000636(ITA);EO0000000637(CHS)Modicon TM2 Digital I/O Modules Hardware GuideEIO0000000028(ENG):EIO0000000029(FRE);EIO0000000030(GER):EIO0000000031(SPA);EO0000000032(ITA);EIO0000000033(CHS)EI0000000039610/20107Modicon TM2 Analog I/O Modules Hardware GuideEIO0000000034(ENG);E1O0000000035(FRE);EIO0000000036(GER);E티00000000037 (ITA);EIO0000000038(SPA);EIO0000000039(CHS)Modicon TM2 High Speed Counter Modules Hardware GuideE1O0000000022(ENG);E1O0000000023(FRE);E1O0000000024(GER);EIO0000000025(SPA);E1O0000000027(CHS)Modicon TWDNOI10M3 AS-Interface Master ModuleE1O0000000608(ENG);Hardware GuideE1O0000000609(FRE);E1O0000000610(GER);EIO0000000611(SPA);E1O0000000612(ITA);E1O0000000613(CHS)You can download these technical publications and other technical information fromour website at www.schneider-electric..Product Related InformationAWARNINGLOSS OF CONTROLThe designer of any control scheme must consider the potential failure modesof control paths and,for certain critical control functions,provide a means toachieve a safe state during and after a path failure.Examples of critical controlfunctions are emergency stop and overtravel stop,power outage and restart.Separate or redundant control paths must be provided for critical controlfunctions.System control paths may include munication links.Consideration must begiven to the implications of unanticipated transmission delays or failures of thelink..Observe all accident prevention regulations and local safety guidelines.1Each implementation of this equipment must be individually and thoroughlytested for proper operation before being placed into service.Failure to follow these instructions can result in death,serious injury,orequipment damage.E目IO00000003961020101 For additional information,refer to NEMA ICS 1.1(latest edition),"SafetyGuidelines for the Application,Installation,and Maintenance of Solid State Control"and to NEMA ICS 7.1(latest edition),"Safety Standards for Construction and Guidefor Selection,Installation and Operation of Adjustable-Speed Drive Systems"or theirAWARNINGUNINTENDED EQUIPMENT OPERATIONOnly use software approved by Schneider Electric for use with this equipment.Update your application program every time you change the physical hardwareconfiguration.Failure to follow these instructions can result in death,serious injury,orequipment damage.User CommentsWe wele your ments about this document.You can reach us by e-mail attechm @schneider-electric..EIO000000039610/2010910E티00000000396 10/2010I/O Configuration GeneralInformation1IntroductionThis chapter provides the general information to configure 1/O expansion modules.What's in this Chapter?This chapter contains the following topics:TopicPage1/O Configuration General Precautions12General Description13Adding an Expansion Module16EI0000000039610/201011I/O Configuration General InformationI/O Configuration General PrecautionsMatch Software and Hardware ConfigurationThe I/O that may be embedded in your controller is independent of the l/O that youmay have added in the form of expansion I/O modules.It is important that the logical1/O configuration within your program matches the physical I/O configuration of yourinstallation.If you add or remove any physical 1/O to or from the l/O expansion bus,it is imperative that you update your application configuration(this is also true for anyfield bus devices you may have in your installation).Otherwise,there is the potentialthat the expansion bus or field bus will no longer function while the embedded 1/Othat may be present in your controller will continue to operate.AWARNINGUNINTENDED EQUIPMENT OPERATIONUpdate the configuration of your program each time you add or delete expansion1/O modules,or you add or delete any devices on your field bus.Failure to follow these instructions can result in death,serious injury,orequipment damage.Use the GetRightBusstatus (see Modicon M238 Logic Controller,System Functions and Variables,M238 PLCSystem Library Guide)function regularly to monitor the expansion bus status.12E目IO0000000396102010