E티00000000608 10/2010Safety InformationImportant InformationNOTICERead these instructions carefully,and look at the equipment to bee familiar withthe device before trying to install,operate,or maintain it.The following specialmessages may appear throughout this documentation or on the equipment to warnof potential hazards or to call attention to information that clarifies or simplifies aprocedure.The addition of this symbol to a Danger or Warning safety labelindicates that an electrical hazard exists,which will result in personalinjury if the instructions are not followed.This is the safety alert symbol.It is used to alert you to potentialpersonal injury hazards.Obey all safety messages that follow thissymbol to avoid possible injury or death.A DANGERDANGER indicates an imminently hazardous situation which,if not avoided,will result in death or serious injury.A WARNINGWARNING indicates a potentially hazardous situation which,if not avoided,canresult in death or serious injury.EI0000000060810/20105CAUTIONCAUTION indicates a potentially hazardous situation which,if not avoided,canresult in minor or moderate injury.CAUTIONCAUTION,used without the safety alert symbol,indicates a potentiallyhazardous situation which,if not avoided,can result in equipment damagePLEASE NOTEElectrical equipment should be installed,operated,serviced,and maintained only byqualified personnel.No responsibility is assumed by Schneider Electric for anyconsequences arising out of the use of this material.A qualified person is one who has skills and knowledge related to the constructionand operation of electrical equipment and the installation,and has received safetytraining to recognize and avoid the hazards involved.6E티00000000608 10/2010About the BookiAt a GlanceDocument ScopeThis manual provides parts descriptions,specifications,wiring diagrams,installation,setup,and troubleshooting information for the Modicon TWDNOI10M3AS-Interface Master Module.Validity NoteThis document has been updated with the release of SoMachine V2.0.The technical characteristics of the device(s)described in this manual also appearonline.To access this information online:StepAction1Go to www.schneider-electric.2In the Search box on the home page,type a model number.Do not type anyblank spaces in the model number.To get information on a grouping similarmodules,you can use the characters *do not use dots or xx's.3Under All,click Products-Product Datasheets and select the model numberthat interests you.4To save or print a data sheet as a.pdf file,click Export to PDF.The characteristics presented in this manual should be the same as those thatappear online.In line with our policy of constant improvement we may revise contentover time to improve clarity and accuracy.In the event that you see a differencebetween the manual and online information,use the online information as yourreference.EI0000000060810/20107Related DocumentsTitle of DocumentationReference NumberModicon TM2 Expansion Modules ConfigurationEIO0000000396(ENG);Programming GuideEIO0000000397(FRE);EIO0000000398(GER);EIO0000000399(SPA:E티O0000000400 (ITA);E티O0000000401(CHS)M238 Controller Hardware GuideE티00000000016(ENG);E티00000000017 (FRE);EIO0000000018(GER);EIO0000000019(SPA5EIO0000000020(TA);E1O0000000021(CS)Twido Programmable Controllers Modular and Compact35011387(ENG);35013236Bases Hardware Guide(FRE);35013235(GER);35013245(SPA);35013246(ITA)You can download these technical publications and other technical information fromour website at www.schneider-electric..Product Related InformationA DANGERHAZARD OF ELECTRIC SHOCK,EXPLOSION OR ARC FLASHDisconnect all power from all equipment including connected devices prior toremoving any covers or doors,or installing or removing any accessories,hardware,cables,or wires except under the specific conditions specified in theappropriate hardware guide for this equipment.Always use a properly rated voltage sensing device to confirm the power is offwhere and when indicated.Replace and secure all covers,accessories,hardware,cables,and wires andconfirm that a proper ground connection exists before applying power to theunit.Use only the specified voltage when operating this equipment and anyassociated products.Failure to follow these instructions will result in death or serious injury.This equipment has been designed to operate outside of any hazardous location.Only install this equipment in zones known to be free of a hazardous atmosphere.8E目IO0000000608102010A DANGEREXPLOSION HAZARDThis equipment is suitable for use in non-hazardous locations only.Failure to follow these instructions will result in death or serious injury.AWARNINGLOSS OF CONTROLThe designer of any control scheme must consider the potential failure modesof control paths and,for certain critical control functions,provide a means toachieve a safe state during and after a path failure.Examples of critical controlfunctions are emergency stop and overtravel stop,power outage and restart.Separate or redundant control paths must be provided for critical controlfunctions.System control paths may include munication links.Consideration must begiven to the implications of unanticipated transmission delays or failures of thelink.Observe all accident prevention regulations and local safety guidelines.1Each implementation of this equipment must be individually and thoroughlytested for proper operation before being placed into service.Failure to follow these instructions can result in death,serious injury,orequipment damage.1 For additional information,refer to NEMA ICS 1.1(latest edition),"SafetyGuidelines for the Application,Installation,and Maintenance of Solid State Control"and to NEMA ICS 7.1 (latest edition),"Safety Standards for Construction and Guidefor Selection,Installation and Operation of Adjustable-Speed Drive Systems"or theirequivalent governing your particular location.AWARNINGUNINTENDED EQUIPMENT OPERATIONOnly use software approved by Schneider Electric for use with this equipment.Update your application program every time you change the physical hardwareconfiguration.Failure to follow these instructions can result in death,serious injury,orequipment damage.EI0000000060810/20109User CommentsWe wele your ments about this document.You can reach us by e-mail attechm schneider-electric..10E티00000000608 10/2010Overview of the AS-InterfaceModuleReminder About the AS-Interface BusGeneralModicon TWDNOI10M3 AS-Interface Master Module is an AS-Interface busconnection.The AS-Interface(abbreviation for Actuator-Sensor-Interface)bus is a field bus,andcan be used to connect sensors/actuators.The AS-Interface system uses a single2-conductor cable to transmit digital or analog information between a bus "master"and sensor/actuator type "slave"devices.An AS-Interface system requires at a minimum three elements:.an AS-Interface power supply providing a 30 Vdc voltage,·a bus master,.one or more slave devices (sensors,actuators and others).These ponents are interconnected by a two-wire cable dedicated to datatransmission and power supply,please see the AS-Interface Reference Guide.EI0000000060810/201011Overview of the AS-Interface Module12E티00000000608 10/2010