E티00000000022 10/2010Safety InformationImportant InformationNOTICERead these instructions carefully,and look at the equipment to bee familiar withthe device before trying to install,operate,or maintain it.The following specialmessages may appear throughout this documentation or on the equipment to warnof potential hazards or to call attention to information that clarifies or simplifies aprocedure.The addition of this symbol to a Danger or Warning safety labelindicates that an electrical hazard exists,which will result in personalinjury if the instructions are not followed.This is the safety alert symbol.It is used to alert you to potentialpersonal injury hazards.Obey all safety messages that follow thissymbol to avoid possible injury or death.A DANGERDANGER indicates an imminently hazardous situation which,if not avoided,will result in death or serious injury.A WARNINGWARNING indicates a potentially hazardous situation which,if not avoided,canresult in death or serious injury.EIO000000002210/20105CAUTIONCAUTION indicates a potentially hazardous situation which,if not avoided,canresult in minor or moderate injury.CAUTIONCAUTION,used without the safety alert symbol,indicates a potentiallyhazardous situation which,if not avoided,can result in equipment damagePLEASE NOTEElectrical equipment should be installed,operated,serviced,and maintained only byqualified personnel.No responsibility is assumed by Schneider Electric for anyconsequences arising out of the use of this material.A qualified person is one who has skills and knowledge related to the constructionand operation of electrical equipment and the installation,and has received safetytraining to recognize and avoid the hazards involved.6E티00000000022 10/2010About the BookAt a GlanceDocument ScopeThis guide describes the hardware implementation of Modicon TM2 HSC Modules.It provides parts descriptions,characteristics,wiring diagrams,installation,andsetup for High Speed Counter(HSC)modules.Validity NoteThe information in this manual is applicable only for TM200HSC206D.products.This document has been updated with the release of SoMachine V2.0.The technical characteristics of the device(s)described in this manual also appearonline.To access this information online:StepActionGo to www.schneider-electric.2In the Search box on the home page,type a model number.Do not type anyblank spaces in the model number.To get information on a grouping similarmodules,you can use the characters *do not use dots or xx's.3Under All,click Products-Product Datasheets and select the model numberthat interests you.4To save or print a data sheet as a.pdf file,click Export to PDF.The characteristics presented in this manual should be the same as those thatappear online.In line with our policy of constant improvement we may revise contentover time to improve clarity and accuracy.In the event that you see a differencebetween the manual and online information,use the online information as yourreference.EI0000000002210/20107Related DocumentsTitle of DocumentationReference NumberModicon TM2 Expansion Modules Configuration ProgrammingEIO0000000396(ENG);GuideEIO0000000397(FRE);EIO0000000398(GER);E티00000000399(SPA);EIO0000000400(ITA;EIO0000000401(CHS)Modicon M238 Logic Controller High Speed Counting M238E티00000000362(ENG);HSC Library GuideE티00000000747 (FRE);EIO0000000748(GER);EIO0000000749(SPA);E티00000000751(CHS)M238 Controller Hardware GuideEIO0000000016(ENG);E1O0000000017(FRE);E티00000000018(GER);E티00000000019(SPA);E티00000000020 (ITA);EIO0000000021(CS)TM2 HSC Instruction SheetAAV86226-00You can download these technical publications and other technical information fromour website at www.schneider-electric..8E目IO000000002210/2010Product Related InformationA DANGERHAZARD OF ELECTRIC SHOCK,EXPLOSION OR ARC FLASHDisconnect all power from all equipment including connected devices prior toremoving any covers or doors,or installing or removing any accessories,hardware,cables,or wires except under the specific conditions specified in theappropriate hardware guide for this equipment.Always use a properly rated voltage sensing device to confirm the power is offwhere and when indicated.Replace and secure all covers,accessories,hardware,cables,and wires andconfirm that a proper ground connection exists before applying power to theunit.Use only the specified voltage when operating this equipment and anyassociated products.Failure to follow these instructions will result in death or serious injury.This equipment has been designed to operate outside of any hazardous location.Only install this equipment in zones known to be free of a hazardous atmosphere.A DANGEREXPLOSION HAZARDThis equipment is suitable for use in non-hazardous locations only.Failure to follow these instructions will result in death or serious injury.EI0000000002210/20109AWARNINGLOSS OF CONTROL.The designer of any control scheme must consider the potential failure modesof control paths and,for certain critical control functions,provide a means toachieve a safe state during and after a path failure.Examples of critical controlfunctions are emergency stop and overtravel stop,power outage and restart.Separate or redundant control paths must be provided for critical controlfunctions.System control paths may include munication links.Consideration must begiven to the implications of unanticipated transmission delays or failures of thelink..Observe all accident prevention regulations and local safety guidelines.1Each implementation of this equipment must be individually and thoroughlytested for proper operation before being placed into service.Failure to follow these instructions can result in death,serious injury,orequipment damage.1 For additional information,refer to NEMA ICS 1.1(latest edition),"SafetyGuidelines for the Application,Installation,and Maintenance of Solid State Control"and to NEMA ICS 7.1 (latest edition),"Safety Standards for Construction and Guidefor Selection,Installation and Operation of Adjustable-Speed Drive Systems"or theirequivalent governing your particular location.AWARNINGUNINTENDED EQUIPMENT OPERATIONOnly use software approved by Schneider Electric for use with this equipment.Update your application program every time you change the physical hardwareconfiguration.Failure to follow these instructions can result in death,serious injury,orequipment damage.User CommentsWe wele your ments about this document.You can reach us by e-mail attechm schneider-electric..10E目IO0000000022102010General Overview and Rules forImplementingIntroductionThis chapter gives a general introduction and the rules for implementing the TM2Analog I/O modules.What's in this Chapter?This chapter contains the following sections:SectionTopicPage1.1General Overview121.2General Rules for Implementing20EI0000000002210/201011General Overview and Rules for Implementing1.1General OverviewIntroductionThis section gives a general introduction to the modules.What's in this Section?This section contains the following topics:TopicPageGeneral Description13Physical Description of the Modules14Dimensions17Accessories1812E티00000000022 10/2010