Sn-명칭설명출력펄스의펄스수를선택F00027PO-36F설정6F00110F01012F01136F00첫째자리채널1로출력하는함목선택둘째자리00:출력주파쉬（최고주파수/100%）01:출력전류（점격전류/100%）2810:전압지령（입력전압/100%）11설정셋째자리채널2로출력하는항목선택넷째자리출력추파쉬（최고주파수/100%）01:출력전류（정격전류/100%）10:전압지령（입력전압/100%）11:직류전압(400V/100%)명칭단위설정값01입력전압（모터정격전압）0~255.0V주1)02최고주파수0.1Hz0.1w400.0Hz03최대전압0.1V0~255.0V주1)04최대전압주파쉬（기저주파수）0.1Hz0.1w400.0Hz05중간출력주파수0.1Hz0.1w400.0Hz06중간출력주파수전압0~255.0V주1)07최저출력주파수0.1Hz0.1w400.0Hz08최저출력주파수전압0.1V0~255.0V주1)09모터점격전류0.1A주310직류제동개시주파수0.1Hz0.1w10.0Hz11직류제동전류1%12정지시직류제동시간0.1s0.025.5s13시동시직류제동시간0.1s0.0w25.5s14주파수지령상한1%15주파수지령하한1%16설정금지주파수10.1Hz0.0w400Hz17설정금지주파수20.1Hz0.0w400Hz18설정금지주파수30.1Hz0.0w400Hz19설정금지주파수범위0.1Hz0.0w25.5Hz20오퍼레이터표시모드10:Hz,2~10:RPM(모터극수)，11~39999：사용자임의표시21임의주파수일치Level0.1Hz0.0w400Hz22주파수일치검출폭0.1Hz0.0w25.5Hz23캐리어주파수상한0.1kHz0.4w15.0kHz24캐리어주파수하한0.1kHz0.4w15.0kHz25캐리어주파수비례게인109926과토크검출L evel1%30200%27과토크검출시간0.1s0.0w25.5s28가속중스돌방지동작Level1%30~200%29가속중스돌방지동작Limit1%30~200%30운전중스돌방지동작Level1%30~200%31모터선간저항0w65.535ohm32토크보상철손065535w33토크보상Limit1V34모터무부하전류1%099%35슬립보상일차지연시간0.1s36이상시재시도횟수0w1037순간정전보증시간0.1s38속도서치동작Level1%39속도서치시간0.1s0w25.5s40최소Base Block시간0.1s0w2.0s41속도서치중의Vf1%42전압복귀시간0.1s0.1w2.0s주1)설정범위는200 V Class의설정범위입니다。400 V Class의경우는2배가됩니다。주3)설정범위는인버터정격전류의10~200%가됩니다。명칭단위설정값01주파수지령10.01Hz0.00-400.00Hz02주파수지령20.01Hz0.00-400.00Hz03주파수지령30.01Hz0.00-400.00Hz04주파수지령40.01Hz0.00-400.00Hz05주파수지령50.01Hz0.00-400.00Hz06주파수지령60.01Hz0.00-400.00Hz07주파수지령70.01Hz0.00-400.00Hz08주파수지령80.01Hz0.00-400.00Hz09jog주파수지령0.01Hz0.00-400.00Hz명칭단위설정값01가속시간10.1s0.0-6000.0502감속시간10.1s0.0-6000.0s03가속시간20.1s0.0-6000.0s04감속시간20.1s0.0-6000.0s05주파수지령Gain0.1%0-1000.0%06주파수지령Bias1%-100-100%07토크보상Gain0.10.09.908모터정격슬립0.1%0.0~9.9%주1)09에너지절약Level Gain1%0-200%10전원투입후의모니터번호11아날로그모니터채널1Gain1%0-255%12아날로그모니터채널2Gain1%0-255%주)An-XX의설정/참조단위는오퍼레이터표시모드Cn-20의설정값에따라다릅니다。공장출하시의설정/참조단위는0.01Hz입니다。주1)Cn-04가100%Level로됩니다。