CAUTIONVerify that the driver rated voltage coincides with the AC powersupply voltage.Failure to observe this caution can result in personal injury or a fire.Do not perform a withstand voltage test of the driver.It may cause semi-conductor elements to be damaged.To connect a braking resistor,follow in APPENDIX A.Improper connection may cause the unit damaged or a fire.Tighten terminal screws.Failure to observe this caution can result a fire.Never connect the AC main circuit power supply to output terminalsU,V and W.The inverter will be damaged and invalidate the guarantee.OPERATION公WARNINGOnly tum ON the input power supply after replacing the front cover.Do not remove the cover while current is flowing.Failure to observe this warning can result in an electrical shock.CAUTIONSince it is easy to change.Operation speed from low to high speed,verify the safe working range of the motor and machine before op-eration.Failure to observe this caution can resuit in personal injury andmachine damage.Do not change signals during operation.The machine or the inverter may be damagedAll the constants of the inverter have been preset at the factory.Do not change the settings unnecessary.MAINTENANCE AND INSPECTIONWARNINGNever touch high-voltage terminals in the driver.Failure to observe this warning can result in an electrical shockReplace all protective covers before powering up the inverter.To remove the cover,make sure to shut OFF the molded-case circuitbreaker.Failure to observe this warning can result in an electrical shockPerform maintenance or inspection only after verifying that theCHARGE LED goes OFF,after the main circuit power supply isturnned OFFThe capacitors are still charged and can be dangerous.Only authorized personnel should be permitted to perform mainte-nance,inspections or parts replacement.Failure to observe this waming can result in an electrical shock.-V-CAUTIONThe control PC board employs CMOS ICs.Do not touch the CMOSelements by hand.They are easily damaged by static electricity.Do not connect or disconnect wires or connectors while power isapplied to the circuit.Failure to observe this caution can result in personal injury.OTHERSWARNINGNever modify the product.Failure to observe this warning can result in an electrical shock orpersonal injury and will invalidate the guarantee.-V-CONTENTS1.RECEIVING12.SPECIFICATIONS…3.DIMENSION DRAWINGS34.INSTALLATION..............55.DESCRIPTION OF TERMINALS1137.FUNCTIONS DESCRIPTION………148.DISPLAY ERROR CODES.............459.HARDWARE PROTECTIVE FUNCTIONS...................4810.PRECAUTIONS…4911.TROUBLESHOOTING5012.APPLICATION……5113.INVERTER SELECTION5514.APPENDIX .........57A.Optional braking resistor57B.Terminal wiring diagram....58591.RECEIVINGThis MS series AC drive has gone through rigorous quality control testsat the factory before shipment.After receiving the AC drive,please checkfor the following(1)No damage is found on each product after shipping.(2)The product is as ordered (check the nameplate,voltage and fre-quency).(3)A set of inverter unit and instruction manual is contained in thepackageFor any irregularity,contact the sales shop where you purchasedimmediately.(4)Description of name plateADLEEPOWER⑧IPM INVERTERVER D 04MODEL MS2-115 VER D04SOFTWARECAPACITY 3.1KVA (1.5KW/2HP)OUTPUT CURRENT8]AHARDWAREADLEE POWERTRONIC CO.,LTD.VERSIONMODEL:MS 2-115MS seriesMax Applicable motor(4 pole)Single PhaseVoltage class102:0.2KW104:0.4KW107:0.75KW2:220V115:1.5KW122:2.2KW12.SPECIFICATIONSModelMS2Voltage1ψ220VAC±10%Model NoMS2-102MS2-104MS2-107MS2-115MS2-122Input Frequency50HZ~60HZ±10%Output VoltageOutput Frequency0.5~800HZOutput1.6A3A5A8A11ARated current(A)Capacity (KVA)0.6 KVA1.9 KVA3.1 KVA4.2 KVALargest motor0.2KW0.4W0.75KW2.2KWKW(4 polesControlSine wave pulse width modulationBrakingRegenerative discharge brakingOver currentCapacity150%of rated current 1 minute)Acceleration time0.1~6000SECDeceleration time0.16000SECFrequencyDigitalUse keyboardfor setting and confirm bysettingAnalogBy frequency knobDisplay typeLED DigitsCooling MethodSelf-cooledSelf-cooledSelf-cooledAir-cooledAir-cooledDimension drawingFiglFig 1Fig 1Weight (NW.KG)1.2KG1.2KG1.3KG1.3KG1.4KG23.DIMENSION DRAWINGSUnit:mm101113Fig 13Unit mm104104115.5Fig 244.INSTALLATIONInadequate environment around installation site and installationsurface can result in damage to the inverter.Before operating the MS series inverter,please check the followingpoints(1)Avoid high temperature,high humidity,easy-to-dew ambient envi-ronment.Don't expose to dust or dirt,corrosive gas,and coolantmist,and direct sunlight.Place the unit in a well-ventilated room.(2)Avoid a place subjected to substantial vibration.(3)When installing the unit within the cabi.Please pay attention toventilation and limit the ambient temperature in between-10C~45℃.(14℉113℉).(4)Use a nonflammable material,such a steel sheet on the wall forinstallation.(The rear side will generate heat)(5)Install the unit always vertically with a marginal spacing around.5 cm4 cm5