[Wiring Precautions]CAUTIONShut off the external power supply for the system in all phases before wiring.Failure to do so may result in damage to the product.Ground the FG pin and FG1 pin to the protective ground conductor dedicatedto the programmable controller.Failure to do so may result in malfunction.Check the rated voltage and pin layout before wiring to the module,andconnect the cables correctly.Connecting a power supply with a different voltage rating or incorrect wiringmay cause a fire or failure.Do not insert the one-touch connector plug for I/O of the one-touch connectortype/connector type pact remote l/O unit into the one-touch connector foranalog 1/O accidentally.Doing so can cause the module to be damaged.Prevent foreign matter such as dust or wire chips from entering the module.Such foreign matter can cause a fire,failure,or malfunction.Always fit a non-wired,one-touch connector plug to the open one-touchconnector for power supply and FG.Not doing so can cause a failure or malfunction.Place the cables in a duct or clamp them.If not,dangling cable may swing or inadvertently be pulled,resulting indamage to the module or cables or malfunction due to poor contact.Do not install the control lines or munication cables together with the maincircuit lines or power cables.Failure to do so may result in malfunction due to noise.When disconnecting the cable from the module,do not pull the cable by thecable part.Loosen the screws of connector before disconnecting the cable.Failure to do so may result in damage to the module or cable or malfunctiondue to poor contact.A-3[Wiring Precautions]ACAUTIONSmoke and fire may occur when an overcurrent flows intermittently for a longperiod of time.To avoid this,configure a safety circuit,such as an externalfuse,to protect the product.[Starting and Maintenance Precautions]CAUTIONDo not touch any pin while power is on.Doing so will cause malfunction.Shut off the external power supply for the system in all phases before cleaningthe module.Failure to do so may cause the module to fail or malfunction.ODo not disassemble or modify the modules.Doing so may cause failure,malfunction,injury,or a fire.Do not drop or apply strong shock to the module.Doing so may damage themodule.Shut off the external power supply for the system in all phases beforemounting or removing the module to or from the panel.Failure to do so may cause the module to fail or malfunction.Before handling the module,touch a grounded metal object to discharge thestatic electricity from the human body.Failure to do so may cause the module to fail or malfunction.[Disposal Precautions]CAUTIONWhen disposing of this product,treat it as industrial waste.A-4●CONDITIONS OF USE FOR THE PRODUCT●(1)Mitsubishi programmable controller ("the PRODUCT")shall be used inconditions;i)where any problem,fault or failure occurring in the PRODUCT,if any,shall not lead to any major or serious accident;andii)where the backup and fail-safe function are systematically orautomatically provided outside of the PRODUCT for the case of anyproblem,fault or failure occurring in the PRODUCT.(2)The PRODUCT has been designed and manufactured for the purpose ofbeing used in general industries.MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY(INCLUDING,BUT NOT LIMITED TO ANY AND ALL RESPONSIBILITYOR LIABILITY BASED ON CONTRACT,WARRANTY,TORT,PRODUCTLIABILITY)FOR ANY INJURY OR DEATH TO PERSONS OR LOSS ORDAMAGE TO PROPERTY CAUSED BY the PRODUCT THAT AREOPERATED OR USED IN APPLICATION NOT INTENDED OREXCLUDED BY INSTRUCTIONS,PRECAUTIONS,OR WARNINGCONTAINED IN MITSUBISHI'S USER,INSTRUCTION AND/OR SAFETYMANUALS,TECHNICAL BULLETINS AND GUIDELINES FOR thePRODUCT.("Prohibited Application")Prohibited Applications include,but not limited to,the use of the PRODUCTin;Nuclear Power Plants and any other power plants operated by Powerpanies,and/or any other cases in which the public could beaffected if any problem or fault occurs in the PRODUCT.Railway panies or Public service purposes,and/or any other casesin which establishment of a special quality assurance system isrequired by the Purchaser or End User.Aircraft or Aerospace,Medical applications,Train equipment,transportequipment such as Elevator and Escalator,Incineration and Fueldevices,Vehicles,Manned transportation,Equipment for Recreationand Amusement,and Safety devices,handling of Nuclear orHazardous Materials or Chemicals,Mining and Drilling,and/or otherapplications where there is a significant risk of injury to the public orproperty.A-5Notwithstanding the above,restrictions Mitsubishi may in its sole discretion,authorize use of the PRODUCT in one or more of the ProhibitedApplications,provided that the usage of the PRODUCT is limited only forthe specific applications agreed to by Mitsubishi and provided further thatno special quality assurance or fail-safe,redundant or other safety featureswhich exceed the general specifications of the PRODUCTs are required.For details,please contact the Mitsubishi representative in your region.A-6REVISIONS*The manual number is given on the bottom right of the cover.Print date*Manual numberRevisionMar.,2003IB(NA)-0800251-AFirst editionJul,2005IB(NA)-0800251-BPartial correctionSAFETY PRECAUTIONSSep,2006IB(NA)-0800251-CPartial correctionChapter 3,Chapter 8Apr,2007IB(NA)-0800251-DPartial correctionSection 2.1,Section 6.2,Chapter 8Sep,2010IBNA)-0800251-EAdditionCONDITIONS OF USE THE PRODUCTPartial correctionSAFETY PRECAUTIONS,About Manuals,Compliance with the EMC and Low VoltageDirectives,Section 2.1,Chapter 3,Section 5.2,Section 6.1,Section 6.2,Chapter 7DeletionSection 5.1Dec.,2011IB(NA)-0800251-FAdditionSAFETY PRECAUTIONS(Chinese)Partial correctionCOMPLIANCE WITH EMC AND LOW VOLTAGEDIRECTIVESJun.,2012IB(NA)-0800251-GPartial correctionSection 5.1,6.2This manual confers no industrial property rights or any rights of any other kind,nor does it confer any patent licenses.Mitsubishi Electric Corporation cannot beheld responsible for any problems involving industrial property rights which mayoccur as a result of using the contents noted in this manual.2003 MITSUBISHI ELECTRIC CORPORATIONA-7CONTENTS2.SPECIFICATION…223.NAMES AND SETTING OF PARTS..............4.LOADING AND INSTALLATION.......84.1 Precautions when handling..........4.2 Installation environment........................85.DATA LINK CABLE WIRING..................5.1 Connection of the CC-Link dedicated cables...............................96.1 Wiring precautions.16.2 Wiring of module with external equipment ..........................127.HOW TO WIRE THE ONE-TOUCH CONNECTOR PLUG..................148.EXTERNAL DIMENSION DIAGRAM.16A-8MANUALThe following manuals are also related to this product.In necessary,order them by quoting the details in the tables below.Detailed ManualManual nameManual number(Model code)Analog-Digital Converter Module type AJ65VBTCU-68ADVN/ADINSH-080401EUser's Manual(13JR65)Related ManualManual nameManual number(Model code)CC-Link System Master/Local Module Type AJ61BT11/A1SJ61BT11IB-66721User's Manual(13J872)CC-Link System Master/Local Module Type1B-66722AJ61QBT11/A1SJ61QBT11 User's Manual(13J873)SH-080394EMELSEC-Q CC-Link System Master/Local Module User's Manual(13JR64)MELSEC-L CC-Link System Master/Local Module User's ManualSH-080895ENG(13JZ41)COMPLIANCE WITH EMC AND LOW VOLTAGE DIRECTIVES(1)Method of ensuring plianceTo ensure that Mitsubishi programmable controllers maintain EMCand Low Voltage Directives when incorporated into othermachinery or equipment,certain measures may be necessary.Please refer to one of the following manuals.User's manual for the CPU module or head module used·Safety Guidelines(This manual is included with the CPU module,base unit,orhead module)The CE mark on the side of the programmable controller indicatespliance with EMC and Low Voltage Directives.(2)Additional measuresTo ensure that this product maintains EMC and Low VoltageDirectives,please refer to one of the manuals listed under (1).A-91.OVERVIEWThis user's manual explains the specifications,names and setting ofparts,wiring and others of Type AJ65VBTCU-68ADVN analog-digitalconverter module (hereafter abbreviated to the "AJ65VBTCU-68ADVN")and Type AJ65VBTCU-68ADIN analog-digital convertermodule (hereafter abbreviated to the "AJ65VBTCU-68ADIN")which isused as a remote device station of a CC-Link system.In this manual,the AJ65VBTCU-68ADVN and AJ65VBTCU-68ADIN aregenerically referred to as the AJ65VBTCU-68ADVN/ADIN.Confirm if the following items are included in the package afterunpacking.Item nameNumber of itemsAnalog-Digital Converter Module type AJ65VBTCU-68ADVNAnalog-Digital Converter Module type AJ65VBTCU-68ADIN12.SPECIFICATION2.1 Performance specificationsThe performance specifications of the AJ65VBTCU-68ADVN/ADIN areshown below.For general specifications,refer to detailed manual.AJ65VBTCU-68ADVNAJ65VBTCU-68ADINProtection classIP1XBVoltage-10 to 0 to 10VDCAnalog(input resistance 1M)input0 to +20mA DCCurrent(input resistance 2502)Digital output16-bit signed binary (-4096 to 4095)16-bit signed binary (-96 to 4095)AccuracyAnalogDigitalAmbientAmbientMax.input rangeoutputtemperaturetemperatureResolution0 to 55C25±5C-10to10W4000User rangeto2.5mVsetting 140001/Ocharacteristics,maximumAJ65VBTCU-resolution,accuracy0 to 5V125mW(accuracy relative to68ADVNmaximum value of digital(Voltage)1 to 5Voutput value)User range4000±0.3%±02%setting 2(0 to 5V)0 to 20mA5μAAJ65VBTCU-4 to 20mA68ADINUser range4000(Current)4μAsetting(0 to 20mA)Maximum conversion speed1ms/channel.Absolute maximum inputVoltage±15VCurrent±30mA2Analog input points8 channels/moduleCC-Link station typeRemote device station(Ver.1 remote device station,Ver.2 remote device station)Ver.1 remote device station (Ver.1 patible slave station)setting:3 stations (32 points for RX and RY,12 points for RWr and RWw)Number of occupied stationsVer.2 remote device station (Ver.2 patible slave station)setting:1 station(32 points for RX and RY,16 points for RWr and RWw,expanded cyclic settings:4 times)Communication cableVer.1.10 patible CC-Link dedicated cable:FANC-110SBH,FA-CBL200PSBH,CS-1102