[INSTALLATION PRECAUTIONS]CAUTIONUse the product in an environment that meets the general specificationscontained in "Type Q80BD-J61BT11N CC-Link system Master/LocalInterface Board User's Manual (For SW1DNC-CCBD2-B)".Using this product in an environment outside the range of the generalspecifications may cause electric shock,fire,malfunction,and damage to ordeterioration of the product.Do not directly touch the conductive area or electronic ponents of theproduct.Doing so may cause malfunction or failure in the product.Fix the product securely with the installation screws and tighten theinstallation screws within the specified torque range.If the screws are loose,it may cause short circuits or malfunction.If the screws are tightened too much,it may cause damage to the screwsresulting in short circuits or malfunction.Always make sure to touch the grounded metal to discharge the electricitycharged in the body,etc.,before touching the product.Failure to do so may cause a failure or malfunctions of the product.Be sure to shut off all phases of the external power supply used by thesystem before installing or removing the product.If all power is not turnedoff,not doing so may cause damage to the product.Securely mount the product to the PCI bus slot of the mounting device.If the product is not mounted correctly,this may lead to malfunctioning,failure or cause the board to fall.When mounting the product,take care not to bee injured by theponents that are installed or surrounding materials.While handling the product,be sure to keep it free of static electricity.Static electric charges may damage the product or result in malfunction.Be sure to turn off the power supply to the applicable station before installingor removing the terminal block.If the terminal block is installed or removed without turning off the powersupply to the applicable station,correct data transmission cannot beguaranteed.Do not drop the product and the terminal block or subject it to any excessiveshock.It may damage the product and the terminal block or result in malfunction.A-3[WIRING PRECAUTIONS]ACAUTIONBe sure to shut off all phases of the external power supply used by thesystem before installing or removing the product and wiring.Not doing so may cause damage to the product.When turning on the power and operating the module after installation andwiring,always attach the puter's main cover.Failure to do so may cause an electric shock.When turning on the power and operating the module after wiring ispleted,always attach the terminal cover that es with the product.There is a risk of malfunction if the terminal cover is not attached.Always ground the SLD terminal of the product and the personal puter tothe protective ground conductor.Not doing so can cause a malfunction.Tighten the terminal screws within the range of specified torque.If the terminal screws are loose,it may cause short circuits or malfunction.If the terminal screws are tightened too much,it may cause damage to thescrew and/or the product,resulting in short circuits or malfunction.Prevent foreign matter such as swarf or wire chips from being attached ontothe product.Failure to do so may cause fires,failure or malfunction.Be sure to fix the wires or cables connected to the product by placing them ina duct or clamping them.If not fixed,cables may be dangled and accidentally pulled,causing damageto the product and cables and malfunction due to bad cable contacts.Do not install the control lines together with the munication cables,orbring them close to each other.Doing so may cause malfunctions due tonoise.When removing the munication cable or power supply cables from theproduct,do not pull the cable.First loosen the screws where the cable is connected to the product and thenremove the cable.Pulling the cable that is connected to the product may cause damage to theproduct and cable or malfunction due to bad cable contacts.Solderless terminals with insulation sleeve cannot be used for the terminalblock.It is remended that the wiring connecting sections of thesolderless terminals will be covered with a marking tube or an insulationtube.Be sure to turn off the power supply to the applicable station before installingor removing the terminal block.If the terminal block is installed or removed without turning off the powersupply to the applicable station,correct data transmission cannot beguaranteed.A-4[WIRING PRECAUTIONS]CAUTIONAlways make sure to power off the system in advance when removing theterminating resistor to charge the system.If the terminating resistor isremoved and mounted while the system is energized,normal datatransmission will not be guaranteed.Use applicable solderless terminals and tighten them with the specifiedtorque.If any solderless spade terminal is used,it may be disconnected when theterminal screw es loose,resulting in failure.Be sure to tighten any unused terminal screws within a tightening torquerange (0.59 to 0.88N.m).Failure to do so may cause a short circuit due to contact with a solderlessterminal.[START UP AND MAINTENANCE PRECAUTIONS]ACAUTIONDo not dismantle or rebuild the product.Doing so could cause failure,malfunction,injury or fire.Be sure to shut off all phases of the external power supply used by thesystem before installing or removing the product.Not doing so may cause failure or malfunction of the Product.Do not touch the terminal while the power is on.Doing so may cause malfunction.Be sure to shut off all phases of the external power supply used by thesystem before cleaning or retightening the terminal screws or modulemounting screws.Not doing so may cause damage to the product.If the screws are loose,it may cause the short circuits or malfunction.If the screws are tightened too much,it may cause damages to the screwsand/or the product,resulting in short circuits or malfunction.Always make sure to touch the grounded metal to discharge the electricitycharged in the body,etc.,before touching the product.Failure to do so may cause a failure or malfunctions of the product.[DISPOSAL PRECAUTIONS]CAUTIONWhen disposing of this product,treat it as industrial waste.A-5Revisions*The manual number is noted at the lower right of the top cover.Print Date*Manual NumberRevisionAug-,2006IB(NA)-0800356-AFirst edition0ct,20071B(NA)-0800356-BCorrectionSection 1.1,Chapter 4,Chapter 5,Chapter 7Jan.,2008IB(NA)-0800356-CCorrectionSAFETY PRECAUTIONS,Chapter 2,Chapter 3,Chapter 5,Section 6.1This manual confers no industrial property rights or any rights of any other kind,nor does it confer any patent licenses.Mitsubishi Electric Corporation cannotbe held responsible for any problems involving industrial property rights whichmay occur as a result of using the contents noted in this manual.2006 MITSUBISHI ELECTRIC CORPORATIONA-6■CONTENTS1.Outline122.Specifications2.1 General specifications...2.2 Performance specifications...42.3 Maximum overall cable distance...............................2.4 CC-Link dedicated cable specifications..........3.Handling........3.1 Precautions when handling.3.2 Installation environment..93.3 Mounting and removing the terminal block.................................95.EMC and Low Voltage Directive.125.1 Requirements for conformance to EMC Directive...........................125.1.1 Standards applicable to the EMC Directive................................125.1.2 Installing devices in the control panel............................135.1.3 Cables.......145.1.4 Noise filter (power supply line filter)..............................................155.2 Requirements for conformance to Low Voltage Directive........................16176.1 Wiring by CC-Link dedicated cable.....177.External Dimensions..............................19A-7About the ManualsThe following manuals are also related to this product.In necessary,order them by quoting the details in the tables below.Related ManualsManual nameManual No.(Model code)CC-Link Ver.2 Q80BD-J61BT11N DriverReference ManualThis manual explains the driver developmentpatible with various OS,for interface boardSH(NA)-080601ENGused in the CC-Link Ver.2 patible PC.(Sold separately)CC-Link System Master/Local Module typeQJ61BT11N User's ManualThis Manual explains the systemSH-080394configuration,Performance specifications,(13JR64)functions,handling,wiring and troubleshootingfor the QJ61BT11N.(Sold separately)Control Communication Link System Master/Local Module type AJ61BT11/A1SJ61BT11User's ManualThis Manual explains the system1B-66721configuration,Performance specifications,(13J872)functions,handling,wiring and troubleshootingfor the AJ61BT11 and A1SJ61BT11.(Sold separately)Control Communication Link System Master/Local Module type AJ61QBT11/A1SJ61QBT11User's ManualThis Manual explains the system1B-66722configuration,Performance specifications(13J873)functions,handling,wiring and troubleshootingfor the AJ61QBT11 and A1SJ61QBT11.(Sold separately)A-81.OutlineThis manual explains the methods of handling the Q80BD-J61BT11N-H1CC-Link System Master/Local interface Board.The Q80D-J61BT11N-H1 CC-Link system Master/Local interface board can beused as a master or local station in the CC-Link system.Unpack the product and confirm that the following products are enclosed.Part nameQuantityType Q80BD-J61BT11N-H1 CC-Link System Master/Local1Interface BoardTerminating resister 110 1/2W (brown,brown,brown)2Terminating resister 130 1/2W(brown,orange,brown)2CC-Link System Master/Local Interface Board User's Manual1ImportantIn the CC-Link system,it is required to connect terminating resistors to both endsof the work.Refer to section "6.1 Wiring by CC-Link dedicated cable"for details on theterminator.11.1 CC-Link versionThere are two types of CC-Link version,i.e.,Ver.1 and Ver.2.(1)Definition of Ver.1.00 and Ver.1.10A product with a cable length of 20cm or longer between stations,which hasbeen achieved by improving the restriction on the conventional cabledistance between the stations,is defined as Ver.1.10.Where as,the conventional product is defined as Ver.1.00.The conditions requiring the cable length to be 20cm or longer betweenstations are as follows:1)All the stations prising a CC-Link system must be of Ver.1.10.2)All the data link cables must be Ver.1.10 patible CC-Link dedicatedcables.POINTIf stations of Ver.1.00 and Ver.1.10 are mixed in a system,the maximum totalcable length and the cable length between stations will be as specified byVer.1.00.Refer to user's manuals noted in the list of related manuals for the maximumoverall cable distance and station-to-station cable length of Version 1.00.(2)Definition of Ver.2The CC-Link Ver.2 board is defined as the Q80BD-J61BT11N-H1 typeCC-Link system master/local interface board supporting the extended cyclicpoints.(3)How to check the versionThe following logo is not shown on the Ver.1.00 patible CC-Link board.On the side of the Ver.1.10 patible CC-Link board,the "CC-Link"logo ismarked.The Ver.2 patible CC-Link board has "CC-Link"logos in the positionsshown below.TCC-LIk V222.Specifications2.1 General Specifications(1)The following table shows the general specifications of the CC-Link Ver.2board.ItemSpecificationsOperatingambient0to55℃temperatureStorage ambient-25to75℃temperatureOperating5 to 95 RH,No condensationambient humidityStorage ambienthumidity5 to 95%RH,No condensationFrequency Acceleration AmplitudeSweep CountConformingWhen there is10 to 57 Hz0.075mmVibrationtointermittent10 times eachvibration57 to 150 Hz9.8m/s2resistanceJ1SB3502,in X,Y and ZWhen there is10 to 57 Hz0.035mmaxisIEC61131-2continuous(80 minutes)vibration57 to 150 Hz4.9m/s2Shock resistance Conforming to JIS B3502,IEC 61131-2(147 m/s2,3 times each in 3 directions XYZ)OperatingenvironmentNo corrosive gas presentOperating height2000 m(6562 ft)or lessInstallation areaOn the control boardOver-voltagecategory*1Pollution rate *22 or less*1:Indicates the distribution area where the device is assumed to be connected,from thepublic power distribution work to the local machine device.Category ll is applied to the devices to which the power is supplied from a fixed equipment.The surge resistance voltage of a rated 300 V device is 2500 V.*2:This is an index which indicates the occurrence rate of the conductive object in theenvironment where the device is used.Pollution rate ll indicates that only non-conductive pollution may occur with a possibility ofgenerating temporary conductivity due to accidental condensation.(2)General specifications of the CC-Link Ver.2 board or the personal puter,whichever is lower,must be satisfied after installation.3