[DESIGN PRECAUTIONS]CAUTIONDo not bunch the control wires or munication cables with the main circuit or power wires,orinstall them close to each other.They should be installed 100mm (3.94 in.)or more from each other.Not doing so could result in noise that may cause malfunction.[INSTALLATION PRECAUTIONS]CAUTIONUse the CC-Link Ver.2 board in an environment that meets the general specifications containedin this user's manual.Using this CC-Link Ver.2 board in an environment outside the range of the generalspecifications may cause electric shock,fire,malfunction,and damage to or deterioration of theDo not directly touch the conductive area or electronic ponents of the CC-Link Ver.2 board.Doing so may cause malfunction or failure in the CC-Link Ver.2 board.Fix the CC-Link Ver.2 board securely with the installation screws and tighten the installationscrews within the specified torque range.If the screws are loose,it may cause short circuits or malfunction.If the screws are tightened too much,it may cause damage to the screws resulting in shortcircuits or malfunction.Always make sure to touch the grounded metal to discharge the electricity charged in the body,etc.,before touching the CC-Link Ver.2 board.Failure to do so may cause a failure or malfunctions of the CC-Link Ver.2 board.Be sure to shut off all phases of the external power supply used by the system before installingor removing the CC-Link Ver.2 board.If all power is not turned off,not doing so may causedamage to the product.Securely mount the CC-Link Ver.2 board to the PCI bus slot of the mounting device.If the CC-Link Ver.2 board is not mounted correctly,this may lead to malfunctioning,failure orcause the board to fall.When mounting the CC-Link Ver.2 board,take care not to bee injured by the ponentsthat are installed or surrounding materials.While handling the CC-Link Ver.2 board,be sure to keep it free of static electricity.Static electric charges may damage the CC-Link Ver.2 board or result in malfunction.Be sure to tum off the power supply to the applicable station before installing or removing theterminal block.If the terminal block is installed or removed without tuming off the power supply to the applicablestation,correct data transmission cannot be guaranteed.Do not drop the CC-Link Ver.2 board and the temminal block or subject it to any excessive shock.It may damage the CC-Link Ver.2 board and the terminal block or result in malfunction.A-2A-2[WIRING PRECAUTIONS]CAUTIONBe sure to shut off all phases of the external power supply used by the system before installingor removing the CC-Link Ver.2 board and wiring.Not doing so may cause damage to the product.When turning on the power and operating the module after installation and wiring,always attachthe puter's main cover.Failure to do so may cause an electric shock.When turning on the power and operating the module after wiring is pleted,always attachthe terminal cover that es with the productThere is a risk of malfunction if the terminal cover is not attached.Always ground the SLD terminal of the CC-Link Ver.2 board and the personal puter to theprotective ground conductor.Not doing so can cause a malfunction.Tighten the temminal screws within the range of specified torque.If the terminal screws are loose,it may cause short circuits or malfunction.If the terminal screws are tightened too much,it may cause damage to the screw and/or the CC-Link Ver.2 board,resulting in short circuits or malfunction.Prevent foreign matter such as swarf or wire chips from being attached onto the CC-Link Ver.2board.Failure to do so may cause fires,failure or malfunction.Be sure to fix the wires or cables connected to the CC-Link Ver.2 board by placing them in aduct or clamping them.If not fixed,cables may be dangled and accidentally pulled,causing damage to the CC-LinkVer.2 board and cables and malfunction due to bad cable contacts.Do not install the control lines together with the munication cables,or bring them close toeach other.Doing so may cause malfunctions due to noise.When removing the munication cable or power supply cables from the CC-Link Ver.2 board,do not pull the cable.First loosen the screws where the cable is connected to the CC-Link Ver.2 board and thenremove the cable.Pulling the cable that is connected to the CC-Link Ver.2 board may cause damage to the CC-Link Ver.2 board and cable or malfunction due to bad cable contacts.Solderless terminals with insulation sleeve cannot be used for the terminal block.It isremended that the wiring connecting sections of the solderless terminals will be coveredwith a marking tube or an insulation tube.Be sure to tum off the power supply to the applicable station before installing or removing theIf the terminal block is installed or removed without tuming off the power supply to the applicablestation,correct data transmission cannot be guaranteed.A-3A-3[WIRING PRECAUTIONS]CAUTIONAlways make sure to power off the system in advance when removing the temminating resistor tocharge the system.If the terminating resistor is removed and mounted while the system isenergized,normal data transmission will not be guaranteed.Use applicable solderless terminals and tighten them with the specified torque.If any solderless spade terminal is used,it may be disconnected when the terminal screw esloose,resulting in failure.Be sure to tighten any unused terminal screws within a tightening torque range(0.59 to 0.88N-m).Failure to do so may cause a short circuit due to contact with a solderless temminal.[START UP AND MAINTENANCE PRECAUTIONS]CAUTIONDo not dismantle or rebuild the CC-Link Ver.2 board.Doing so could cause failure,malfunction,injury or fire.Be sure to shut off all phases of the external power supply used by the system before installingor removing the CC-Link Ver.2 board.Not doing so may cause failure or malfunction of the CC-Link Ver.2 board.Doing so may cause malfunction.Be sure to shut off all phases of the external power supply used by the system before cleaningor retightening the terminal screws or module mounting screws.Not doing so may cause damage to the product.If the screws are loose,it may cause the short circuits or malfunction.If the screws are tightened too much,it may cause damages to the screws and/or the CC-LinkVer.2 board,resulting in short circuits or malfunction.Always make sure to touch the grounded metal to discharge the electricity charged in the body,etc.,before touching the CC-Link Ver.2 board.Failure to do so may cause a failure or malfunctions of the CC-Link Ver.2 board.[DISPOSAL PRECAUTIONS]CAUTIONWhen disposing of this product,treat it as industrial waste.A-4A-4The manual number is given on the bottom left of the back cover.Print Date米Manual NumberRevisionJun.,2005SH(NA)-080527ENG-AFirst PrintingSH(NA)-080527ENG-BCorrectionSection 2.2.1,Section 8.4.1,Section 8.4.3,Chapter 9,Section 17.1.1Jun,2006SH(NA)-080527ENG-CCorrectionSection 2.2.4,Section 3.2,Section 8.6,Section 17.2.1Mar,2007SH(NA)-080527ENG-DCorrectionGeneric Terms and Abbreviations,Section 2.2.1,Section 8.4.1,Section 10.1.2.Section 11.2.Section 11.4.Section 11.8AdditionSection 11.3.5,Section 11.3.6,Section 11.70ct,2007SH(NA)-080527ENG-ECorrectionGeneric Terms and Abbreviations,Section 1.1.Section 1.3,Section 2.2.1,Section 4.2.3,Chapter 7,Section 8.4.1,Section 9.1,Section 11.3,Section 17.1.4,Section 17.2.1,Section 17.3.1,Appendix 3.2Section 8.4.2 to 8.4.3 changed to Section 8.4.3 to 8.4.4AdditionSection 8.4.2,Appendix 7Jan,2008SH(NA)-080527ENG-FCorrectionPrecautions for use,Generic Terms and Abbreviations.Chapter 1.Section 2.2Section 2.2.1,Section 2.2.3,Section 3.1,Section 4.2.1,Section 4.2.2,Section 4.2.3,Section 4.2.4,Section 4.4.5,Section 5.2,Section 5.2.2,Section 5.2.3,Section 5.2.4,Section 5.3.Section 5.3.1.Section 5.3.2.Section 6.1.Section 7.1.1,Section 7.1.2,Section 8.2.1,Section 8.2.2,Section 8.4.1,Section 8.6,Section 9.3.6,Section 9.3.7,Section 9.3.8,Section 9.3.11,Section 10.1.1,Section 10.1.2.Section 12.2.1,Section 12.5.1,Section 13.1.2,Section 13.2.2,Section 14.1.2,Section 14.2.2,Section 15.2.1,Section 16.2.1,Section 17.1.4,Section 17.2.1,Section 17.6,Appendix 3.1.2,Appendix 3.1.3A-5A-5The manual number is given on the bottom left of the back cover.Print DateManual NumberRevisionMay,2008SH(NA)-080527ENG-GModel addition]Q81BD-J61BT11CorrectionPrecautions for use.Generic Terms and Abbreviations.Product List.Section 1.1.Section 1.3.Section 2.1.Section 2.2.1.Section 2.2.2,Section 2.2.3,Section 2.2.4,Section 3.1,Section 3.2.Section 4.4.7.Section 5.2.Section 8.3.Section 8.4.1,Section 8.4.3,Section 8.4.4,Section 8.6,Section 8.7.2,Section 9.1.1,Section 10.1.2,Section 11.3,Section 12.1,Section 12.5.2,Section 13.1.1,Section 13.1.5,Section 13.2.1,Section 13.2.5,Section 14.1.1,Section 14.1.5,Section 14.2.1,Section 14.2.5,Section 15.1,Section 15.5.2,Section 16.1,Section 16.5.2,Section 17.1.3,Section 17.3.1,Section 17.3.2,Appendix 1.1Appendix 1.2,Appendix 2.3,Appendix 3.Appendix 3.2AdditionAppendix 8.1,Appendix 8.2Sep,2008SH(NA)-080527ENG-HCorrectionSection 3.2Oct,2008SH(NA)-080527ENG-ICorrectionGeneric Terms and Abbreviations,Section 3.3,Section 10.1.2Japanese Manual Version SH-080526-1This manual confers no industrial property rights or any rights of any other kind,nor does it confer any patentlicenses.Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial propertyrights which may occur as a result of using the contents noted in this manual.2005 MITSUBISHI ELECTRIC CORPORATIONA-6A-6Precautions for use(1)Operating environment of the personal puter usedRefer to Section 2.2 Applicable Systems in this manual.(2)When using the CC-Link Ver.2 board as a standby master stationRefer to Section 2.2.2 for binations of modules when using the CC-LinkVer.2 board as a standby master station.(3)When using the CC-Link Ver.2 board as a master stationWhen using the CC-Link Ver.2 board as a master station,any of local modulescannot be used as a standby master station.(4)Restrictions on the CC-Link Ver.2 board installationInstalling the CC-Link Ver.2 board and CC-Link Ver.1 board to the sameputer and using both of them is not allowed.(5)Multi-thread municationMulti-thread munication is not supported.(6)InstallationWhen a CC-Link Ver.2 board is used on a personal puter in whichSWnDNF-CCLINK has been installed,uninstall SWnDNF-CCLINK first,theninstall the SW1DNC-CCBD2-B that is provided with the CC-Link Ver.2 boardOverwrite installationWhen performing an overwrite installation,install the program in the samefolder in which the previous program is installed.(8)Start menuAfter the utility software is uninstalled,the program name may still be displayedin the Start menu.In this case,restart the personal puter.Software versions of the CC-Link system master and local modulesWhen reading/writing data from/to other stations using the transienttransmission function in the CC-Link system,use the following software versionfor the CC-Link master and local modules to be accessed.Model nameSoftware versionRemarkQJ61BT11NAmy of the versions of theQJ61BT11module can be used.AJ61QBT11A1SJ61QBT11Not accessible if the softwareVersion N or laterAJ61BT11version is Mor earlier.A1SJ61BT11(10)Multiprocessor-based personal putersFor details on the patible operating system and driver software versionwhen using multiprocessor-based personal puters,refer to (1)(b)inSection 2.2.1.(11)Compatibility with the hyper-threading technologyFor details on the patible operating system and driver software versionwhen using the hyper-threading technology on the personal puter,refer to(1)(b)in Section 2.2.1.(12)Transient transmission functions of the CC-Link boardTransient transmission is not allowed to slave station No.64 on the CC-Linksystem.A-7A-7(13)PerformanceThe system performance using the CC-Link Ver.2 board differs according tothe performance/loaded condition of the personal puter,the processingcontents of the application software,and the type of the interface board.Usethe product after reviewing the system configuration and processing contents ofthe software in advance.For details of the CC-Link Ver.2 board performance,refer to Chapter 5,DATALINK PROCESSING TIMES.(14)Combination of ROM version and S/versionWhen using CC-Link Ver.2 board ROM version 2B or later,use SW packageversion 1.06G or later.A-8A-8INTRODUCTIONThank you for purchasing the Type Q80BD-J61BT11N/Q81BD-J61BT11 CC-Link System Master/LocalInterface Board.Please read this manual thoroughly to fully understand the functions and performances of the Type Q80BD-J61BT11N/Q81BD-J61BT11 CC-Link System Master/Local Interface Board in order to use the productproperly.Please be sure to deliver this manual to the end users.CONTENTSSAFETY PRECAUTIONSA 5Precautions for use .....A 7INTRODUCTION........A-gCONTENTS...........Manuals…A-16How to Use this Manual......A-17Generic Terms and Abbreviations..A-191-1to1-141.1 Features of the CC-Link Board......1.2 Features of the CC-Link System............131.3 Combinations of Boards with Existing Software.1-102 SYSTEM CONFIGURATION2-1to2-102.1 Overall Configuration......212.2 Applicable Systems...242.2.1 Applicable personal puters and number of boards that can be installed....................2-42.2.2 Notes on the system configuration......272.24 CC-Link VerSion2-103 SPECIFICATIONS31to3-63.1 General Specifications..........313.2 Performance Specifications.3.2.1 Maximum overall cable distance (for Ver.1.00)343.2.2 Maximum overall cable distance (for Ver.1.10)363.3 CC-Link Dedicated Cable Specifications ......4 FUNCTIONS41to4-484.1 Function List…4.2 Basic Functions.....4.2.1 Communication with remote 1/O stations ............434.2.2 Communication with the remote device stations..4-54.2.3 Communication with the local stations.......4104.2.4 Communication with the intelligent device station .............416A-9A-94.3 Functions for Improving System Reliability..............4.3.1 Disconnecting a data link faulty station and continuing the data link with only normal stations(slave station disconnect function)4-224.3.2 Automatically reconnecting a disconnected data link faulty station when it returns to normal(auto return function)..........4-234.3.3 Retaining the device status of a data link faulty station(setting the input data status from a data link faulty station)...4-244.3.4 Continuing the data link even when the master station is faulty (standby master function)..........4-254.4.1 Creating a program that contains modules to be added in the future(reserved station function)..............4-344.4.2 Powering off a station in operation without detecting an error(error invalid station setting function).4-354.4.3 Checking operations for each station (data link stop/restart).4-364.4.4 Station number duplicate check4-364.4.6 Reducing the reserved points of the remote l/O stations (Remote I/O station points setting).....4-384.4.7 Increasing the number of cyclic points (Remote ver.2 mode,Remote additional mode)..4-394.5 Transient Transmission Functions ......4484.5.1 Performing transient transmission (functions)...4-485 DATA LINK PROCESSING TIMES5-1to5-185.2 Cyclic Transmission Processing Time .........535.2.1 Master station (CC-Link Ver.2 board)remote 1/O station..............535.2.2 Master station(CC-Link Ver.2 board)remote device station (Ver.2 patible slave station)........5-55.2.3 Master station(CC-Link Ver.2 board)local station (programmable controller)er.2 patible slave station）……….…5-95.2.4 Master station (CC-Link Ver.2 board)intelligent device station........5-135.3 Transient Transmission Processing Time.5-145.3.1 Master station (CC-Link Ver.2 board)local station (programmable controller)...5-145.3.2 Master station (CC-Link Ver.2 board)intelligent device station............5-165.4.1 Status of the master station and remote l/O station at error.............5-175.4.2 Status of the remote device station,local station,standby master station and intelligent deviceStation at erTO5-186 PARAMETER SETTINGS6-1t06-106.2 Example of Parameter Settings (Remote ver.1 mode).....6-56.2.1 Master station work parameter settings..6-56.2.2 Local station work parameter settings..........6-66.3 Example of Parameter Settings (Remote ver.2 mode)..6-76.3.1 Master station work parameter settings6-76.32 Local station work parameter settings..6-86.4 Example of Parameter Settings(Remote additional mode).....696.4.1 Master station work parameter settings.....6-96.4.2 Local station work parameter settings..............A-10A-10