5 Operation Inspection10000P15.1 Routine Inspection1.Check that the wiring of analog input meets the requirements (see 1.310000200002.Check that the extension cable of EC10-5AMis property inserted in theextension port.3.Check that the 5V and 24V power supplies are not overloaded.Note:BThe digital circuit of EC10-5AM is powered by the basic module throughMode0,D0=0.D1=10.000Mode0,D0=-500.D1=2000the extension cable.Digital input 10,000 outputs 10VDigital input 2000 outputs 5V (or 20mA)4.Check the application and make sure the operation method andDigital input 0 outputs OVDigital input 0 outputs 1Vparameter range are correct.Digital input -10,000 outputs-10V Digital input-10,000 outputs-5V5.Set the EC10 basic module to RUN state.Figure 3-6 Changing output channel characteristics5.2 Fault Inspection4 Application ExampleIn case of abnormality,check the following items4.1 Basic Applicationthe status of the POWER indicatorExample:The EC10-5AM module address is 1(for the addressing ofOFF:check the exlension cable connection and the basic modulechannels 1,2,3 and 4 for voltage signal input (-10V-10V),set the●the analog wiringaverage sampling times to 4,and use data registers D1,D2,D3 and D4the status of the 24V indicatorto receive the average value;set output channel to mode 0 to output 10VON:24Vdc power supply normal;voltage signal,and use D5 element.Set extension module type as shownin Figure 4-1,and set actual parameters of exlension module.Figure 4-2OFF:24Vdc power supply possibly faulty,or EC10-5AM is faulty.shows the setting of input channel 1 and output channel 1.Set the otherthe status of the RUN indicatorthree input channels respectively in the same way.Flash quickly:EC10-5AM in normal operation;Flash slowly or OFF:check the data in BF M#300Notice1.The warranty range is confined to the PLC only.2.Warranty period is 18 months,within which period Emerson NetworkPower conducts free maintenance and repairing to the PLC that has anyfault or damage under the normal operation conditions.3.The start time of warranty period is the delivery date of theproduct,of which the product SN is the sole basis of judgment.PLCwithout a product SN shall be regarded as out of warranty.4.Even within 18 months,maintenance will also be charged in thefollowing situations:◆Damages incurred to the PLC due to mis-operations,which are notin pliance with the User Manual:Damages incurred to the PLC due to fire,flood,abnormal voltage.etc;BC10-5AMConfigurationDamages incurred to the PLC due to the improper use of PLCfunctions.5.The service fee will be charged according to the actual costs.If there isDany contract,the contract prevails.6.Please keep this paper and show this paper to the maintenance unitwhen the product needs to be repaired.7.If you have any question,please contact the distributor orour panyENP Services ChinaEmerson Network Power Co.,Ltd.Address:No.1 Kefa Rd.,Science Industry Park,Nanshan District518057,Shenzhen ChinaHomepage:www.emersonworkpower..Figure 4-2 Setting special module parametersE-mail:support@emersonwork..To validate the parameter setting,you still need to pile and downloadthe parameters.You can set and query D elements through the interfaceVersionV1.0or by us ing the MOV instruction in user program.Revision dateAugust 24,2006MOV D5 2000 is a user program that makes the output channel outputBOM31011339Copyright 2006 by Emerson Network Power Co.,Ltd.For further details,see EC20/EC10 Series PLC Programming Manual.All rights reserved.The contents in this document are subject to change4