7.2型号说明8.3拨码开关产品型号说明见下图ECCT系列控制器的面板提供一个5位拨码开关，具体位置请参见1】外形ECA20-MB 40结构.拨码开关1~4位组合成特定的数字，上电后保存在SD40:上电后拨码开关的变化不会反映到SD40.此功能可使相同的用户程序应用于不同的工序。附件类型。MB:存储卡拨码开关第5位用于设置CAN通信口的可调电阻。具体请参见&2CAW通产品系列号：1,29上电运行与例行保养7.3存储卡操作说明上电运行接线完毕后逐项检查连接情况，确保无异物掉入机壳内，散热通畅。存储卡上提供了两个按钮及一个存储卡写保护开关。具体说明请参见下表。1.接通控制器的电源，POWER灯应点亮：部件名称丝印功能说明2.启动PC上的ControlStar软件，将编制好的用户程序下载到控制器：用户文件导入按钮M©mony,>PLC将用户文件从存储卡导入控制器3.下载程序校验完毕，把运行控制开关拨到ON位，RUN灯应点亮，若ERR用户文件导出按钮PLC->Memory将用户文件从控制器导出到存储卡灯点亮，表明用户程序或系统有错误，请按《EC系列小型可编程控制器编程Lok:存储卡写保护：WR:存储卡可写参考手册》的说明排除错误，直到正确为止：4.再把控制器外部系统的电源合上，进行系统调试，7.4存储卡密码功能例行保养为保护ECCT系列控制器内部程序的知识产权，同时防止恶意破坏，存储卡需例行保养检查应注意如下方面：1.保证控制器工作环境的整洁，避免异物、灰尘落入机内：ECCT系列控制器内部的密码相同的情况下，存储卡才能与ECCT系列控制器交换用户文件。2。保持控制器良好的通风散热：3.所有接线连接及接线端子固定牢固，状态良好。8ECCT系列控制器新增特性10常见问题及解决方案8.1输入点数字滤波当控制器不能正常工作时，请依次检查：控制器的前8个输入点(X0一X7)可分成两组通过软件设定滤波时间(0~1。电源线路的连接及相关开关和保护电器的状况，确保控制器已可靠供电：60ms),分组方式可通过ControlStar灵活设置.2.用户端子的接线是否牢固：3。模式选择开关的位置是否正确。若完成上述检查后仍无法工作，请联系艾默生当地办事处或代理商。保修协议1。保修范围指可编程控制器本体。滤波常数还可通过指令进行设置，REFF、REFF2分别用于设置第一、二组滤2.能期为土八个月，保修期内正常使用情况下，产品发生故障或损坏，我波常数。司免费维修。8.2CAN通信口4。即使在保修期内，如发生以下情况，将收取一定的维修费用：口的相关参数。该CAN通信口的可调电阻通过拨码开关的第5位控制。拨码●不按用户手册操作导致的机器故障：开关具体位置请参见11外形结构·由于火灾、水灾、电压异常等造成的机器损坏：ECCT系列控制器提供三条CAN通信指令：●将可编程控制器用于非正常功能时造成的损坏。■CANXMT,单一CANID多数据桢发遂指令：5。服务费按实际费用计算，如另有合同，以合同优先的原则处理。CANMXMT,多CANID多数据楨发送指令：6。请您务必保留此卡，并在保修时出示给维修单位。CANRCV,CAN接收指令，接收指定CAND的数据，7.如您有问题可与代理商联系，也可直接与我司联系。艾默生网路能源有限公司中国区客户服务中心ECCT系列控制器提供CAN通信口的数据楨接收完成中断，中断子程序号48，地址：深圳市南山区科技工业园科发路一号：郎编：518057中断使能SM9。任何一个CAN的数据桢都引发中断。CAN数据桢信息保存在SD元件中，如下表所示.客户服务热线：400-887-6510地址名称客户服务投诉热线：0755-86010800SD280SD281SD282当前顿字符数资料版本：V12SD283-SD290归档时间：2009-09-08B0M编号：31011609版权所有，保留一切权利。内容如有政动，恕不另行通知。1.2 Model DescriptionECCT Programmable Compositive ControllerThe model description of ECCT series controller is shown below.ECC T-16 14 BRA1DA added).Start from 1 by timeThis manual is a quick guide to the design,installation,connection andsequence,Ike 1,2,3 and so on.Themaintenance of ECCT programmable positive controller (for short,Power input mode (A:220ac input:D:ECCT series controller).By briefing the hardware specifications,features24Vdc nput):N:no extemal power inputand usage,introducing the options,and answering the FAQs,it offersOutput mode.R:relay output:information that you may need on-site.If you need detailed productT:transistor output;N:no output.Module type.Manual.In that case,you can consult your distributor.1 Product Introduction-Input points.In ths example,16.T type1.1 Appearance And StructureEmThe appearance and structure of ECCT controller are shown in the figurebelow.1.3 Terminal IntroductionThe signal input terminals output terminals,and the power supplyterminals of ECCT series controller,are located on the controller front panel,as shown in 1.1 Appearance And Structure.Different controllers have different terminal layouts.The following table liststhe mon terminals,as well as their definitions,of all controllers.Silk printDefinitionL/NLive and neutral (terminals of 220Vac power supply)PG+24VAuxiliary DC power supply for user equipment,worktogether with COMCOMNegative pole of the auxiliary 24V power supplyS/SInput mode selection:sink input when in connection with+24V,or source input when in connection with COMNull,for isolation.Leave it suspendedTo Customers:ECCT-1614BRAThank you for choosing our products.To improve the product and providebetter service for you,could you please fill in the form after the product hasSilk printDefinitionbeen operated for 1 month,and mail or fax it to our Customer ServiceX0-X17Digital input terminals.Input signals are generated whenused together with COMCenter?We will send you an exquisite souvenir upon receiving the pleteProduct Quality Feedback Form.Furthermore,if you can give us someDigital output terminal,group 0 The COMx of differentadvices on improving the product and service quality,you will be awarded aY2-Y6.C0M1Digital output terminal,group 1 output groups arespecial gift.Thank you very much!Y7-Y10,C02Digital output terminal,group 2Emerson Network Power Co.,Ltd.Product Quality Feedback FormECCT-1614BRA1Customer nameTeleDefinitionAddressZip codeX0-X17Digital input terminals.Input signals are generatedwhen used together with COMModelDate of useYO-Y1.COMODigital output terminal,group 0 The COMx of differentMachine SNY2~Y6,COM1Digital output terminal,group 1output groups areDigital output terminal,group 2 isolated from eachAppearance orY11-Y15,COM3Digital output terminal,group 3 otherstructure+CAN-CAN munication portAnalog output terminals.AV+,AV-AV+:positive voltage output AV-:negative voltageoutputPackage2 Power SupplyMaterialThe specification of the built-in power of ECCT series controller and thepower that the controller can provide for extension modules are lisled in theQuality problemtable below.during usageUnit Min.Rating Max.NoteInput voltageVac 100220240Normal startup and work rangeSuggestion aboutrangeA1.590Vac input,100%output5V/GNDRatedmA/500The total power of outputs5V/GND and 24V/GND:s9.7W.Address:No.1 Kefa Rd.,Science Industry Park,Nanshan District,518057.output24V/GNDmA300Max.output power,or the totalShenzhen,PRCcurren24V/COM mA/600/of all routes fully loaded:24.1WTel:+88755860105813 Digital 1/O FeaturesItemRelay outputfrom each other3.1 Input Features And Signal SpecificationsVoltage feature220Vac;24Vdc,no polarity requirementAccord with output electric specification (see the nextHigh speed inputs (XO -X7)Ordinary inputstable)Source/sink mode,Overall differenceHigh driving voltage,large currentSignal input modeselectable through S/SApplicationLoads with low action frequency such as intermediateterminalrelay,contactor coil,and LEDsTest voltage24VdcElectric Input3.3k04.3k0The output electric specification is listed in the following tableresistanceRelay outputmeterInput being ON Extemal circuit resistance smaller than 4000s250Vac,s30Vdcsupply/O terminals exceptX0 ~X7 are capable ofCircuit isolationMechanical isolation of relaydigital filtering.FilteringOperation indication Relay output contacts closed,LED ontime (set through userFiltering time:aboutprogram):0~60msopen circuit10msMinimum load2mA/DC5VX0 ~X5:capable of high-speed counting.Resistive4A/2 pointinterrupt,and pulse capturing:X6 ~X7:capable ofHigh s peed functioninterrupt and pulse capturing:XO~X5:max.Max.load10A/5 points,using a COMcounting frequency up to 10kHz;The sum of inputoutput220Vac.80VAloadfrequency:<60kHzLightening220Vac,100WOnly one:S/SON/OFF response20ms MaxThe maximum frequency of the counter input terminal is limited.timeFrequencies above that limit may result in incorrect counting or abnormalYO,Y1 max.outputsystem operation.You should properly arrange the input terminal and selectfrequencysuitable external sensors.Output monThe controller S/S terminal is used to select signal input mode betweenY11~Y15-COM3.The mon terminals aresource and sink.You can select the sink input mode by connecting the S/Sisolated from each otherterminal with the +24V terminal,which enables you to connect NPN typeFuse protectionNonesensor.See the following figures for the cable connection.4Analog Output Features4.1 Analog Terminal DescriptionECCT series controller provides integrated AD/DA function,ideal for thesmall,low-cost and integrated resolution that meets your requirement foranalog control.The ECCT controller that supports analog 1/O is listed in the following tableModelAnalog outputChannel numberVoltage outputECCT-1614BRA11YesThe terminals that are related to analog signals are listed in the followingtable.3.2Output Features And Signal SpecificationsDescriptionThe output circuit is shown in the following figureAV+Positive voltage signal outputAnalog outputAV-Negative voltage signal output4.2Specification Of Analog OutputcoSpecificationspeed50msAnalog output0~10Vdc (external loadVoltage outputrangeresistance:2kQ 1MQ)Digital outputRange:0~1000ResolutionVoltage output10mV210Total regulationAnalog output±1.5%No isolation between the analogcircuit and digital circuit5Communication PortECCT series controller provides two serial asynchronous municationports:PORT1 (RS485)and PORTO(RS232,with mini DINB socket).Supp0 rted baud rates:115200,57600.38400,19200.9600,4800,2400,The relay output and transistor output are pared in the following table.1200bps.The location of the munication port is shown in 1.1Relay outputAs the dedicated port for user programming,PORTO can be forcedlyDry contact output.Output when in ON state,or noOutput modechanged to the programming protocol through the mode selection switch,output when in OFF statewhose location is shown in 1.1 Appearance And Structure.The controllerDivided into several groups.Each terminal group hasoperation state and PORTO protocol are related,as listed below.Common terminalone mon terminal COMn that fits the controlcircuits of different levels.The COMs are isolated2Switching settingStatePORTO protocolCableCSARemendedCable lug andProgramming protocol,Modbus protocol,modelheat-shrink tubeONRunfree-port protocol,or N:N work protocolAC power cable (LAWG12.18H1.5/14 round insulated(Ecbus),as determined by user program andN),DC power1.0-2.0mmable24V+,24-)ug.or tinned cable lugTM (ON->TM)RunH2.0/14 round insulatedForcedly change to programming protocolEarth cable(⑨)2.0mmAWG12TM (OFF->TM)Stopug,or tinned cable endIf the system configuration of user programInput signal cable0.8-1.0m㎡AWG18,20is free-port protocol,it converts to)UT1-3or OT1-3OFFStopprogramming protocol automatically afterOutput signalstop;or system protocol keeps unchangedcable (Y)0.8-1.0m㎡AWG18.20The shape and pin layout of PORTO are shown in the following figure.Use screws to fix the lugs of ready-made cables to the controller terminals.PORTOMake sure the screws are fixed to the right positions.The fastening torque isPORT10.5~0.8Nm,which ensures reliable connection without damaging the screw.3GNDThe remended cable processing-method is shown below.RXD32TXDA reliable GND cable can improve the safety and IMS of the controller.During the installation,connect the PG terminal of the controller with thesuch as inverters.It uses Modbus protocol or RS485 free-port protocol andground electrode.It is remended to use the AWG12-16 cable,keep itcan control multiple equipment through work.The port uses screw-fixedas short as possible,and use an independent grounding device.Avoidterminals.The munication cable (remended type:twisted pair)issharing mon routes with the ground cable of other equipmentuser self-made.(especially those with strong interference),as s hown in the following figure6InstallationECCT series controller is applicable to locations that meet Installationcategory ll and Pollution Degree 2.If PLC extension modules are used,connect the ground cable of each6.1 Installation Sizesmodule to the ground electrode separately,as shown below.The sizes of ECCT series controller and their installation holes are shown inthe following figure (unit:mm).2940430Connecting power cable and grounding cableThe connections of AC power and auxiliary power supply are shown below.6.2 LocationECCT series controller must be installed horizontally on cabi backboard.To achieve optimal ventilation,keep at least 15cm of clearance at both thetop and bottom of the controller.Do not put any heat-generating devicesbelow.See the following figure.7 Memory Card IntroductionAs an option of ECCT series controller,ECA20-MB40 memory card can beconnected to the controller by inserting the connecting terminal on thememory card to the memory card port on the controller.See 1.16.3 Installation ProceduresAppearanoe And Structure for the location of the memory card port on thecontroller.You can copy user files from controller to the memory card or viceversa.The user file contains user program,system block and data block.controller onto the backboard of the electric cabi through the four fixingThe memory card is not hot-pluggable.holes on the casing of the controller.See 1.1 Appearance And Structurefor the locations of the fixing holes.7.1 Appearance Structure6.4 Cable Connection And SpecificationCable specificationWhen wiring,use multi-strand copper wire and ready-made insulatedterminals to ensure the quality.The remended model and theCross-Sectional Area (CSA)of the cable are shown in the following table.7.2 Model DescriptionDIP switch after power-on.This function can apply the same user programto different work stages.Bit 5 of the DIP switch is used to set the varistor ofThe product model is des cribed in the following figure.CAN munication port.See 8.2 CAN Communication Port for details.9 Power-on Operation MaintenancePower-on operationCheck the cable connection carefully.Make sure that the controller is cleaninside out and the ventilation duct is clear.1.Power-on the controller,the POWER indicator should be ON.7.3 Operation Description2.Run software ControlStar on the host,and download the piled userThe memory card provides two buttons and a write-protection switch.Seeprogram to the controller.the following table for details.3.After checking the download program,set the mode selection switch toPart nameSilk printFunction descriptionthe ON position,the RUN indicator should be on.If the ERR indicator is onUser file downloadDownload user files from memoryinstead,the user program or the system is faulty.Look up in the EC SenesbuttonMemory->PLCcard to controllerMicro-PLC Programming Manual and remove the faultUser file uploadPLC->Memorypload user files from controller to4.Power on the PLC exlemal system to start system debugging.buttonmemory cardWrite-protectionRoutine maintenanceWR/Lockock:write disabled:WR:writableswitchDo the following:1.Keep the work environment clean.Prevent alien objects and dust from7.4 Password Protectionentering the controller.To protect the intellectual property of the internal program of ECCT series2.Keep the ventilation heat dissipation of the controller in good conditioncontroller,and to protect the controller,you need to set upload/download3.Ensure that the cable connections are reliable and in good condition.password for the memory card through ControlStar.The memory card canexchange user files with the controller only when the memory card10 TroubleshootingIf the controller is faulty,take the following measures:8 New Features Of ECCT Series Controller1.Check the connection of the power supply cable,and the related switchesprotective devices.8.1 Digital Filtering Of Input PointsThe first eight input points of the controller (XO -X7)can be dassified into3.Ensure that the mode selection switch is in the right position.If all the conditions are normal but the PLC still does not work,pleaseThe classification can be done flexibly through ControlStar.contact Emerson local office or your distributor.Notice1.The warranty range is confined to the controller only.2.Warranty period is 18 months,within which period Emerson NetworkPower conducts free maintenance and repairing to the controller that hasary fault or damage under the normal operation conditions.3.The start time of warranty period is the delivery date of the productof which the product SN is the sole basis of judgment Controller without aThe filtering constant can also be set through instruction.Instructions REFFproduct SN shall be regarded as out of warranty.and REFF2 are used to set the filtering times of group one and group two.4.Even within 18 months,maintenance will also be charged in the followingsituations:8.2 CAN Communication PortDamages incurred to the controller due to mis-operations,which areECCT series controller provides one CAN munication port.You can setnot in pliance with the User Manual;parameters related to the CAN munication port through ControlStarDamages incurred to the controller due to fire,flood,abnormalThe varistor of CAN munication port can be set through bit 5 of the DIPswitch.See 1.1 Appearance And Structure for the location of the switch.voltage,etc;ECCT series controller provides three CAN munication instructions:Damages incurred to the controller due to the improper use ofcontroller functions.CANMXMT,multi-CANID multi-dataframe transmitting instruction5.The service fee will be charged according to the actual costs.If there isCANRCV,CAN receiving instruction.Receive data from designatedany contract,the contract prevails.CANID6.Please keep this paper and show this paper to the maintenance unit whenthe product needs to be repaired.For details,see the online help of ControlStar For ECCT (V1.0 or later).ECCT series controller provides dataframe reception-plete interrupt of7.If you have any question,please contact the distributor or our panyCAN munication port.Interrupt subprogram No.:48.Interrupt enabling:directly.SM69.Any CAN dataframe can trigger the interupt.The CAN dataframe isstored in SD elements,as listed in the following table.ENP Services ChinaAddressNameEmerson Network Power Co.,Ltd.SD280Address:No.1 Kefa Rd.,Science Industry Park,Nanshan District 518057,SD281MID of the frame being receivedShenzhen ChinaSD282Number of characters of current frameHomepage:www.emersonworkpower..SD283-SD290No.0-7 characterE-mail:support@emersonwork..8.3 DIP SwitchVersion:V1.2Revision date:September 8,2008 BOM:31011609ECCT series controller provides a 5-bit DIP switch on the front panel,asCopyright 2008 by Emerson Network Power Co.,Ltd.shown in 1.1 Appearanoe And Structure.Bits 1 ~4 can generate figuresAll rights reserved.The contents in this document are subject to changethat are stored in SD40 after power-on.The figures will not be affected bywithout notice.