DVP04PT-E2ConnectorEuropean standard removable terminal block(Pin pitch:5mm)Operation:0C~55C(temp.),5~95%(humidity),Pollution degree2Operation/storageStorage:-25C~70C (temp.),5~95%(humidity)Vibration/shockInternational standards:IEC61131-2,IEC 68-2-6(TEST Fc)/immunityIEC61131-2 IEC 68-2-27(TEST Ea)The modules are numbered from 0 to 7 automatically by their distanceSeries connection tofrom MPU.No.0 is the closest to MPU and No.7 is the furthest.DVP-PLC MPUMaximum 8 modules are allowed to connect to MPU and will notoccupy any digital VO points.Functions SpecificationsDVP04PT-E2Celsius(C)Fahrenheit(F)InputImpedanceAnalog input channel4 channelsDigital data format2's plement of 16 bitsResponse time200ms /each channelOverall accuracy±0.3%when in full scale(25°C,77F)+0.6%when in full scale within the range of 0~55C,32~131FApplicable sensor3-WIRE PT100/NI100/PT1000/NI1000,0~3000 input impedancetypeCurrent excitation1.53mAPT100N100),200uA(PT1000/NI1000)PT100:-180°C-800CPT100:-292F~1,472FNI100:-112F-338FRange of inputPT1000:-180℃~800℃PT1000:-292F-1.472℉NI1000:-112°F-338°FPT100:K-1.800-K8.000PT100:K-2.920-K14.720Range of digitalNI100:K-1,120-K3.3800-3000conversionPT1000:K-1,800-K8,000PT1000:K-2,920~K14,720NI1000:K-800~K1,700N1000:K-1,120~K3,380Resolution16bts(0.1C)16bits(0.1月16bits(0.12)Average functionSupported.Available for setting up sampling range in CR#8~CR#11.Range:K1~K100.Self-diagnosisUpper and lower bound detection in all channelsOptical coupler isolation between digital circuits and analog circuits.No isolation among analog channels.500VDC between digital circuits and GroundIsolation500VDC between analog circuits and Ground500VDC between analog circuits and digital circuits500VDC between 24VDC and GroundControl RegisterCR#Attrib.Register contentDescription0Set up by the system:0RModel nameDVP04PT-E2 model code=H'0082#1RFirmware versionDisplay the current firmware version in hex.#2R/WCH1 Input mode settingInput mode:Default H'0000.Take CH1 forexample:#3RCH2 Input mode settingMode1(H'0001):Nl100:-80°C-170℃#4R/CH3 Input mode settingMode2(H'0002):PT1000:-180°C~800°℃Mode3(H'0003):Nl1000:-80℃~170℃CH4 Input mode settingMode4(H'0004):0-3002.CR#Attrib.Register contentDescriptionMode-1(H'FFFF):Channel 1 unavailable#70R/WTemperature unit settingSelect the temperature unit(Celsius C/Fahrenheit F).Default=HO(C)CH1 sampling rangeCH2 sampling rangeSet sampling range at CH1~CH4Range K1 ~K100CH3 sampling rangeDefault K10CH4 sampling range#12XRAverage temperaturemeasured at CH1Average temperature measured at CH1#13XRAverage temperatureCH3.measured at CH2Temperature unit:set in CR#7#14XRAverage temperaturemeasured at CH3#15XRAverage temperatureAverage temperature measured at CH4.measured at CH4Temperature unit:set in CR#7RPresent temperature#20Xmeasured at CH1#21XRPresent temperaturemeasured at CH2Present temperature measured at CH1~CH4.#22Present temperatureRTemperature unit:set in CR#7measured at CH3#23Present temperatureXRmeasured at CH4#280R/Set the adjusted Offset value of Ch1 Ch4.Default KO#29R/WAdjusted Offset value of CH2Range:K-400~K400Temperature unit:set in CR#7#30R/WAdjusted Offset value of CH3Definition of Offset at Ch1 Ch4 inDVP04PT-E2:#310R/WAdjusted Offset value of CH4Deviation digital value from the target value.#40R/Function:Set value changingprohibitedProhibit set value changing in CH1~CH4Function:Save all the set#41R/Save all the set values.Default =H'0000valuesFunction:Return to default#42RSet all values to default setting,DefaultsettingH'0000#43RError statusRegister for storing all error status.See thetable of error status for more information.#1000R/WFunction:Enable/Disable limitEnable/Disable the upper and lower bounddetectiondetection function.Default=H'0000.#101XRUpper and lower bound statusDisplay the upper and lower bound value,Default =H'0000Set value of CH1 upper boundSet value of CH2 upper boundSet value of CH1~CH4 upper bound.DefaultSet value of CH3 upper bound=K32000.Set value of CH4 upper boundSet value of CH1 lower boundSet value of CH2 lower boundSet value of CH1~CH4 lower bound.DefaultSet value of CH3 lower bound=K-32000.#111Set value of CH4 lower bound-4-CR#Attrib.Register contentDescriptionSymbols:O:When CR#41 is set to H'5678,the set value of CR will be saved.X:set value will not be saved.R:able to read data by using FROM instruction.W:able to write data by using TO instruction.CR#43:Error status value.See the table below.DescriptionbitoK1(H1)Power supply errorbit6K64(H'40)CH4 Conversion errorbit1K2(H2)Hardware errorbit9K512(H0200)Mode setting errorbit2K4(H4)Upper lower boundbit10K1024(H'0400)Sampling range errorerrorbit3K8(H'8)CH1 Conversion errorbit11K2048(H0800)Upper/lower boundsetting errorbit4K16(H'10)CH2 Conversion errorbit12K4096(H1000)Set value changingprohibitedCommunicationbit5K32(H20)CH3 Conversion errorbit13K8192(H2000)breakdown on nextmoduleNote:Each error status is determined by the corresponding bit(b0-b13)and there may be morethan 2 errors occurring at the same time.0=normal;I errorPID Control RegistersCR#Attrib.Register contentDescriptionCH4Please set the temperature value#120#140#160#180RMSet temperatureaccording to proper range of eachvaluesensor type.Default=Ko#121#141#161#181Sampling time (s)Range:K1 K30 (s).Default K2Proportional control constant.#122#142#162#182KpDefault=K121#123#143#163#1830KIntegral constant.Default K2,098#124#144#164#184KoDerivative constant.Default K-29#125#145#165#1850Upper limit of I valueUpper limit of I value.Default KO#126#146#166#186Lower limit of I valueLower limit of I value.Default KO#127#147#167#187I valueCurrent accumulated offset value#128#148#168#188oHeating/cooling0:Heater,1:Cooler.Default KO#129#149#169#189Upper limit of outputUpper limit of output.Default=K32,000#130#150#170#190Lower limit of outputLower limit of output.Default K0#131#151#191ROutput percentageOutput percentage (Unit:0.1%)#132#152#172#192ROutput width (ms)Width of control output.Unit:ms#133#153#173#193ROutput cycle (ms)Cycle of control output.Unit:ms#134#154#174#194ROutput volumeOutput volume#135#155#175#195PID RUN/STOP0:STOP.1:RUN.Default KO#136#156#176#1960:Disabled,1:Auto-tuning.DefaultAuto-tuning=K0Explanation on Special Registers D9900~D9999-5When DVP-ES2 MPU is connected with modules,registers D9900~D9999 will bereserved for storing values from modules.You can apply MOV instruction to operatevalues in D9900~D9999When DVP-ES2 MPU is connected with DVP04PT-E2,the configuration of specialregisters is as below.ModuleModuleModuleModuleModuleModuleModuleModule#1#2#36#7DescriptionD1320D1321D1322D1323D1324D1325D1326D1327Model CodeD9900D9910D9920D9930D9940D9950D9960D9970CH1 averagetemperatureCH2 averageD9901D9911D9921D9931D9941D9951D9961D9971temperatureD9902D9912D9922D9932D9942D9952D9962D9972CH3 averagetemperatureCH4 averageD9903D9913D9923D9933D9943D9953D9963D9973temperatureNote 1:D9900 -D9999 are average input values of CHI -CH4 and the sampling range is KI-K100When the sampling range is set to KI,the values displayed in D9900-D9999 are current values.You can use:1.ES_AlO Configuration Function of WPLSoft or 2.FROM/TO instructions (CR#8-CR#11)to set the sampling range as K1.Adjust PT Conversion CurveUsers can adjust the conversion curves according to the actual needs by changing theOffset value (CR#28 CR#31).Offset in DVP04PT-E2:Deviation digital value from the target value.Equation for temperature input Mode0 Mode3:0.1'Y=Digital output,X=measured input temperatureEquation for input impedance Mode4:0.1=3000/3,000X(Ohm)Y=Digital output,X=measured Input impedance·Mode2:Digital outputDigital output+8.,000+14,720+4.000+7,360MeasuredMeasuredI temperature input-292℉i temperature input0+400+800'℃+736-1,800-2.920-6-·Mode1·Mode3Digital outputDigital output+1.700+3,380MeasuredMeasuredI temperature input-112℉i temperature input0-800-1.120Digital output+3.000Measured inputimpedance3002Mode 0.2 of CR#2~CR#5-180℃~800℃(-1800-8000)，-292℉~1472℉(-2920-14720)Mode 1,3 of CR#2~CR#5-80℃~170°℃(-800-1700)，-112℉~338°F←1120-3380)Offset (CR#28 CR#31)Deviation digital value corresponds to 0C/FMode 4 of CR#2 ~CR#5Offset (CR#28~CR#31)Deviation digital value corresponds to 0Q-7-測器(PT1003線10023850PPM°C(DIN43760J1SC16041989)/N1100/PT1000/N11000),將其轉换成16位元的數位信號。使用者可選擇攝氏溫度（°C)或華氏(F)温度，攝D9999特殊暫存器使用說明。从本安装說明書提供給使用者電氣規格·功能規格、安装配線之相關注意事項。其他群細之程式設計及指合說明請見DVP-ES2操作手冊【模粗篇】，選購之周邊装置群細說W本機爲開放型(OPEN TYP曰機殼，因此使用者使用本機時，必須將之安装於具防麈、防潮及免於電擊衝擊意外之外殼配線箱內。另必須具備保護措施（如：特殊之工具或编匙寸可打開)防止非維護人員操作或意外衝擊本體，造成危險及損壞。从交流輸入電源不可連接於輸入出信號端，否則可能造成骰重損壞，請在上電之前再次確認電源配線·請勿在上電時觸摸任何喘子。本體上之接地端子⊕務必正確的接地，可提高產品抗雜訊能力·脫落式输出/入端子0000000000000VO模粗固定扣直接固定孔·群細尺寸圖請参閱英文版直碼1之Figure2,單位：mm。·外部配線NI100/NI1000PT100/PT10001.53mA(PT100)/CH1200uA(PT1000)00000(01+11+FEAGMUX0-30001.53mACH404+14+14-FEAG接至電源模+5VDC/DC+15V24V轉换器AG+-15V(接地抗阻1002以凡